A320飞机维护手册 AMM FUSELAGE 机身3(150)

曝光台 注意防骗 网曝天猫店富美金盛家居专营店坑蒙拐骗欺诈消费者

R  WARNING : USE SOLVENTS/CLEANING AGENTS, SEALANTS AND OTHER_______ 
R  SPECIAL MATERIALS ONLY WITH A GOOD SUPPLY OF AIR. 
R  OBEY THE MANUFACTURERS INSTRUCTIONS. 
R  PUT ON PROTECTIVE CLOTHING. 
R  DO NOT GET THEM IN YOUR MOUTH. 
R  DO NOT SMOKE. 
R  DO NOT BREATHE THE GAS. 
R  THESE MATERIALS ARE POISONOUS, FLAMMABLE AND SKIN 
R  IRRITANT. 
R  GET MEDICAL HELP IF YOUR SKIN OR EYES BECOME IRRITATED. 
R  1 Apply the SPECIAL MATERIALS (Material No. 05-002) to the_ 
R  screws (68). 
R  (p) Put the access covers (69) in position and install and tighten 
R  the screws (68). 
R  (q) Put the bonding straps (71) in position and install and tighten 
R  the nuts (74), bolts (75) and the washers (76) (Ref. TASK 20-28-
R  00-912-004). 
R  (r) Disconnect the hoisting sling from the hoisting lugs. 
R  (s) Remove the hoisting lugs from the tail cone and apply the SPECIAL 
R  MATERIALS (Material No. 05-002) to the lugs. 
R  (t) Install the hoisting lugs in the hoisting points with their 
R  eye-ends in.

 

R (u) Protective treatment.

R  WARNING : USE SOLVENTS/CLEANING AGENTS, SEALANTS AND OTHER_______ 
R  SPECIAL MATERIALS ONLY WITH A GOOD SUPPLY OF AIR. 
R  OBEY THE MANUFACTURERS INSTRUCTIONS. 
R  PUT ON PROTECTIVE CLOTHING. 
R  DO NOT GET THEM IN YOUR MOUTH. 
R  DO NOT SMOKE. 
R  DO NOT BREATHE THE GAS. 
R  THESE MATERIALS ARE POISONOUS, FLAMMABLE AND SKIN 
R  IRRITANT. 
R  GET MEDICAL HELP IF YOUR SKIN OR EYES BECOME IRRITATED. 
R  1 Apply the SPECIAL MATERIALS (Material No. 05-052) on the_ 
R  hoisting points. 
R  (2) Connect the APU fuel line: 
R  (Ref. Fig. 405/TASK 53-58-11-991-011) 
R  (a) Apply the COMMON GREASE (Material No. 04-012) to the new O-rings 
R  (51) and install them on the shrouds (38) and (33). 
R  (b) Install the shroud (38) with the sleeve (54) on the fuel hose 
R  (37). 
R  (c) Remove the SLIDE CONE - APU FUEL and connect the nut (35) to the 
R  fitting (36). 
R  (d) Tighten the nut (35) (Ref. TASK 20-21-12-911-001) and safety it 
R  with the lockwire, MISCELLANEOUS (Material No. 19-018). 
R  (e) Install the shroud (38) in the sleeve (54) and slide the sleeve 
R  (54) on the shroud (38) and the shroud (33). 
R  (f) Install the retaining springs (34) and safety them with the 
R  lockwire, MISCELLANEOUS (Material No. 19-018). 
R  (g) Align the shroud (38) with the sleeve (54) and the shroud (33) 
R  and install the clamp (52). 
R  (h) Put the bonding straps (32), (46) and (53) in position and 
R  install and tighten the bolts (43), the washers (44) and the nuts 
R  (49) (Ref. TASK 20-28-00-912-004). 
R  (3) Install the APU air-intake flap (Ref. TASK 49-16-43-400-002). 

 

R  (4) Connect the ball-bearing control cable to the APU air-intake 
R  flap-diverter (Ref. TASK 49-16-41-400-002). 
R  (5) Install the bleed air duct: 
R  (Ref. Fig. 403A/TASK 53-58-11-991-010-A) 
R  (a) Remove the blanking covers from the bleed air ducts and install a 
R  new air seal (9) in the bleed air duct (4). 
R  (b) Put the bleed air duct (4) on the bleed air duct (13) and move it 
R  rearward. 
R  (c) Move the bleed air duct (4) forward and align it with the bleed 
R  air duct (3). 
R  (d) Install, but do not tighten, the V-clamp (1). 
R  (e) Put the rod assemblies (8) in position. 
R  (f) Install and tighten the bolts (7), the washers (6) and the nuts 
R  (5). 
R  (g) Make sure that the bleed air duct (4) is correctly aligned and 
R  TORQUE the V-clamp (1) to between 0.57 and 0.79 m.daN (50.44 and 
R  69.91 lbf.in). 
R  (h) Put the bonding strap (14) in position and tighten the screws 
R  (15), the washers (16) and the nuts (17) (Ref. TASK 20-28-00-912-
R  004). 
R  (i) Install the overheat sensing element 19HF (Ref. TASK 36-22-17-
R  400-001). 
R  (j) Install the sleeve (2), the sleeve (11) and the lock sleeve (12). 
　
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址：A320飞机维护手册 AMM FUSELAGE 机身3(150)