Nov 01/04
R
CES -------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
53-42-14-000-001 Removal of the AFT Cargo-Compartment Floor-Panels Zone 150 53-42-14-400-001 Installation of the AFT Cargo-Compartment
Floor-Panels Zone 150
ASRM 51-11-00-001
ASRM 51-22-00-001
NTM 534156-Part.6
ASRM 51-73-00-001 (for corrective action)
ASRM 51-74-00-001 (for corrective action)
ASRM 53-46-11-101 (for corrective action)
53-41-00-991-048 Fig. 661
3. Job Set-up
__________
R **ON A/C 001-049, 051-099, 101-149, 201-299, 301-399,
Subtask 53-41-00-010-122
A. Get Access
(1)
Open the AFT cargo-compartment door (Ref. TASK 52-30-00-860-001).
(2)
Put an access platform in position below the cargo door.
(3)
If installed, remove the rear additional center tank (Ref. AMM 28-11-27, Page Block 401).
(4)
In the AFT cargo-compartment, remove the floor-panels 151DF, 151GF (Ref. TASK 53-42-14-000-001).
(5)
Remove the insulation blankets from the inspection area (Ref. TASK 25-80-00-000-001).
NOTE : Identify the insulation blankets for installation.
____
R **ON A/C 151-199, 401-499,
Subtask 53-41-00-010-122-A
A. Get Access
(1)
Open the AFT cargo-compartment door (Ref. TASK 52-30-00-860-001).
(2)
Put an access platform in position below the cargo door.
(3)
If installed, remove the rear additional center tank (Ref. AMM 28-11-27, Page Block 401).
(4)
In the AFT cargo-compartment, remove the floor-panels 151VG, 151ZG (Ref. TASK 53-42-14-000-001).
(5)
Remove the insulation blankets from the inspection area (Ref. TASK 25-80-00-000-001).
NOTE : Identify the insulation blankets for installation.
____ **ON A/C ALL
Subtask 53-41-00-860-061
B. Preparation of the Inspection Areas
(Ref. Fig. 661/TASK 53-41-00-991-048)
(1) Make sure that the surfaces of the inspection areas are clean and smooth.
WARNING : OBEY THE MANUFACTURER'S INSTRUCTIONS WHEN YOU USE
_______ THIS/THESE MATERIAL/S. USE PROTECTIVE CLOTHING, RUBBER GLOVES, GOGGLES AND A MASK.
Lock Fittings of the Aft Cargo Compartment Door Figure 661/TASK 53-41-00-991-048
R EFF : CES ALL 53-41-00 Page C632 Nov 01/04
WARNING : MAKE SURE THAT THERE IS A GOOD FLOW OF AIR THROUGH THE WORK
_______ AREA WHEN YOU USE SPECIAL MATERIALS. IF YOU GET ONE OF THESE MATERIALS ON YOUR SKIN, IN YOUR MOUTH OR IN YOUR EYES : -FLUSH IT AWAY WITH A FLOW OF CLEAN WATER FOR BETWEEN 10 AND 15 MINUTES. -GET IMMEDIATE MEDICAL AID IF IRRITATION OCCURS. DO NOT BREATHE THE FUMES FROM THE MATERIAL. DO NOT SMOKE WHEN YOU USE THE MATERIAL. DO NOT USE THE MATERIAL NEAR A FLAME, SPARKS OR SOURCES OF HEAT. THESE MATERIALS ARE DANGEROUS : THEY ARE POISONOUS, FLAMMABLE AND SKIN IRRITANTS.
(2)
If necessary, clean the surfaces of the inspection areas with the CLEANING AGENTS (Material No. 11-004) and a MISCELLANEOUS (Material No. 19-003).
(3)
Make sure you remove the used sealant.
(4)
If necessary, make the surfaces of the inspection areas smooth with the abrasive cloth, grade 280.
(5)
Make sure the inspection areas are clean and dry before you continue.
(6)
Do a visual inspection of the surfaces of the inspection areas. Look for damage, and defects in the shape of the surfaces.
(7)
If you find damage :
(a)
Refer to the ASRM (Ref. ASRM 51-11-00-001) for the classification of the damage.
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址：A320飞机维护手册 AMM FUSELAGE 机身3(64)
