(c)
Remove the cup washer (22).
(d)
Remove the bolt (5).
(e)
Remove the nut (30), the screw (28) and the washers (29).
(f)
Remove the bonding jumper (27).
(g)
Remove and discard the cotter pin (12).
(h)
Remove the nut (9) and the washer (11).
(i)
Remove and discard the tabwasher (7).
(j)
Remove the retaining ring (3) and the sleeve (6).
(k)
Remove the bushes (4).
(9)
Disconnect the upper fixed bearing as follows:
(a)
Open the closed edges of the lockwasher (2) and the tabwasher (7).
(b)
Remove the nut (1) and remove and discard the lockwasher (2).
(c)
Remove the cupwasher (22).
(d)
Remove the bolt (5).
(e)
Remove the nut (30), the screw (28) and the washers (29).
(f)
Remove the bonding jumper (27).
(g)
Remove and discard the cotter pin (12).
(h)
Remove the nut (9) and the washer (11).
(i)
Remove and discard the tabwasher (7).
R EFF : 004-049, 055-099, 101-149, 151-199, 53-56-11Page 411 201-299, 301-399, 401-499, Aug 01/05
CES
(j)
Remove the retaining ring (3) and the washer (21).
(k)
Carefully pull the sleeve (6) out of the link assembly and remove the bushes (20) and the washer (21).
(10)
Remove the spacer (13) as follows:
(a)
Remove and discard the cotter pin (26).
(b)
Remove the nut (25), the bolt (24) and the washers (10).
(c)
Remove the spacer (13).
(11)
Remove the links (19) and (23).
(12)
Remove the bolts (8) from the link (19).
R EFF : 004-049, 055-099, 101-149, 151-199, 53-56-11Page 412 201-299, 301-399, 401-499, Aug 01/05
CES **ON A/C ALL
TASK 53-56-11-400-001
Installation of the Support Fittings of the Trimmable Horizontal Stabilizer (THS)
NOTE : The installation procedures are given for the left Support Fittings; the
____ installation procedures for the right Support Fittings are almost the same.
1. Reason for the Job
__________________
Self Explanatory
2. Job Set-up Information
______________________
A. Fixtures, Tools, Test and Support Equipment
-------------------------------------------------------------------------------REFERENCE QTY DESIGNATION -------------------------------------------------------------------------------
No specific nonmetallic scraper
No specific warning notice
No specific Torque Wrench : range 0.20 to 3.60 m.daN
(2.00 to 26.00 lbf.ft) No specific Torque Wrench : range 1.00 to 10.00 m.daN
(8.00 to 75.00 lbf.ft) SL90-313-4375 1 TOOL - INSTALLATION, TAB-WASHERS STA-LOK NSA5454 SL90-374-4375 1 WRENCHES - NOTCHED, TIGHTENING OF NUTS NSA5454 98AMS172327000 1 HOOK WRENCH - ADAPTER 98D27408406000 1 DISTANCE STRUT - FRAME 77
B. Consumable Materials
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
Material No. 04-004 USA MIL-PRF-23827 TYPE I
SYNTH.ESTER BASED GREASE HIGH PRESSURE
(Ref. 20-31-00)
Material No. 09-013 USA MIL-PRF-81733 TYPE I CLASS A
CORROSION INHIBITING BRUSH CONSISTENCY
(Ref. 20-31-00)
R Material No. 11-003 USA ASTM D 740 METHYL-ETHYL-KETONE (Ref. 20-31-00)
Material No. 15-007 AIB TN 10138 TYPE II GRADE 1 CORROSION PREVENTIVE TEMPORARY PROTECTIVE COMPOUND (Ref. 20-31-00)
EFF : ALL
53-56-11Page 413
C. Expendable Parts
-------------------------------------------------------------------------------
FIG.ITEM |DESIGNATION |IPC-CSN
-------------------------------------------------------------------------------
2 lockwashers 53-56-04 42 -160 7 tabwashers 53-56-04 42 -180 12 cotter pins 53-56-04 42 -195 26 cotter pin 53-56-04 42 -280 31 O-rings 53-56-04 42 -040 43 cotter pin 55-16-37 01A-020 43 cotter pin 55-16-37 01B-020
D. Referenced Information
-------------------------------------------------------------------------------
REFERENCE DESIGNATION
-------------------------------------------------------------------------------
12-22-53-640-001 Lubrication of Trimmable Horizontal Stabilizer
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址：A320飞机维护手册 AMM FUSELAGE 机身3(133)
