R 1EFF : 051-099, 1 31-36-00Page 276 1 1 May 01/05 1 1 1CES 1
R **ON A/C 001-049, 051-099, 101-105, 201-202,
Subtask 31-36-00-865-060
C. Remove the safety clip(s) and the tag(s) and close this(these) circuit breaker(s):
-------------------------------------------------------------------------------PANEL DESIGNATION IDENT. LOCATION -------------------------------------------------------------------------------121VU CFDS/CFDIU/SPLY 2TW J18 121VU CFDS/CFDIU/BACK/UP 8TW J17 121VU DATA/LOADER/SPLY 3TD J16 121VU FDIU & QAR 8TU K17 121VU AIDS/DMU 4TV K15 121VU ENGINE/ENG1 AND 2/EVMU 1EV R44
4. Procedure
_________
R **ON A/C 001-049, 051-099, 101-105,
Subtask 31-36-00-710-055
A. System Software Load Procedure
NOTE : The standard vendor software has 3 disks for the system software.
____ You must use the System Software disk, which is available in the floppy disk compartment.
NOTE : The software P/N is shown in the IPC
____
-------------------------------------------------------------------------------ACTION RESULT -------------------------------------------------------------------------------
1. On the Portable Data Loader On the PDL display:
(PDL):
-
Put the ON/OFF switch to the ON - The MDDU READY indication shows. position.
-
Put the software disk 1TV1 (DMU - These indications show in a short
SYSTEM SW) disk into the PDL. time:
READY,
WAIT RESPONSE,
R 1EFF : 001-049, 051-099, 101-105, 201-202, 1 31-36-00Page 277 1 1 May 01/05 1 1 1CES 1
-------------------------------------------------------------------------------
ACTION RESULT -------------------------------------------------------------------------------TRANSF IN PROG.
-Wait until the TRANSF COMPLETE - TRANSF COMPLETE shows after the load indication comes on. procedure is completed correctly.
NOTE : Usually the time to load the software is between 3 and 5 minutes. If
____ the load procedure is completed after some seconds, then the disk is incorrect or the A/C is not in Ground configuration (Engine stopped and Landing Gear compressed).
- Push the EJECT button and - The MDDU READY indication shows.
remove the software disk 1TV1.
- Put the ON/OFF switch in the
OFF position.
2. On the MCDU: On the MCDU display:
- Push the MCDU MENU mode key. - The AIDS prompt must show.
Subtask 31-36-00-710-065
B. Database Software Upload Procedure NOTE : You can monitor the upload procedure of the database files on the
____
AIDS SOFTWARE LOAD STATUS page.
-------------------------------------------------------------------------------ACTION RESULT -------------------------------------------------------------------------------
1. On the MCDU:
-Push the MCDU MENU mode key.
2. On the Portable Data Loader (PDL):
-
Put the ON/OFF switch in the ON position.
-
Put the software disk 1TV2 (DMU SET-UP DB) disk into the PDL.
On the MCDU display:
-
The AIDS indication shows.On the PDL display:
-
The MDDU READY indication shows.
-These indications show in a shorttime: READY,
R 1EFF : 001-049, 051-099, 101-105, 1 31-36-00Page 278 1 1 May 01/05 1 1 1CES 1
-------------------------------------------------------------------------------ACTION RESULT
-------------------------------------------------------------------------------WAIT RESPONSE, TRANSF IN PROG.
-Wait until the TRANSF COMPLETE - TRANSF COMPLETE indication shows
indication comes on. after the upload procedure is completed correctly.
NOTE : Usually the time to load the software is between three and five
____ minutes. If the load procedure is completed after some seconds, then the disk is incorrect or the A/C is not in Ground configuration (Engine stopped and Landing Gear compressed).
-Push the EJECT button and - The MDDU READY indication shows. remove the software disk 1TV2.
-Put the ON/OFF switch in the OFF position.
R **ON A/C 001-049, 051-099, 101-105, 201-202,
5. Close-up
________
R **ON A/C 001-049, 051-099, 101-105,
Subtask 31-36-00-860-051
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址：A320飞机维护手册 AMM 指示/记录系统 4(11)
