-------------------------------------------------------------------------------
12-12-29-611-001 Fill the Hydraulic Fluid Reservoir with a Hand Pump 12-12-29-611-002 Fill the Hydraulic Fluid Reservoir with a Hydraulic Service Cart 29-00-00-864-001 Put the Related Hydraulic System in the Depressurized
Configuration before Maintenance Action 29-00-00-910-002 Safety Procedures of the Hydraulic System 29-14-00-614-001 Depressurization of the Hydraulic Reservoirs 29-14-00-614-002 Pressurization of the Hydraulic Reservoirs through
the Ground Connector 29-22-00-720-001 Operational Test of the Manual Deployment of the Ram
Air Turbine. Functional Test of the Ram Air Turbine 29-22-00-869-001 Extension of the Ram Air Turbine (RAT) on the Ground 29-22-00-869-002 Retraction of the Ram Air Turbine (RAT) on the Ground 29-22-51-991-010 Fig. 408
1EFF : 001-049, 051-061, 101-105, 201-203, 1 29-22-51Page 477 1 1 Config-1 Aug 01/05R 1 1 1CES 1
3. Job Set-up
__________ Subtask 29-22-51-865-070
A. Make sure that this(these) circuit breaker(s) is(are) open, safetied and tagged
-------------------------------------------------------------------------------PANEL DESIGNATION IDENT. LOCATION -------------------------------------------------------------------------------106VU CSM/G /EV/MAN/SPLY 6XE B04 121VU HYDRAULIC/RAT/SPLY/EXTN/SOL1 2803GE P33
**ON A/C 001-049, 051-061, 101-102, 201-202,
121VU HYDRAULIC/RAT/CTL 2801GE P32 **ON A/C 103-105, 203-203,
121VU HYD/RAT/CTL 2801GE P32 **ON A/C 001-049, 051-061, 101-105, 201-203,
Subtask 29-22-51-860-066
B. Aircraft Maintenance Configuration
WARNING : OBEY THE HYDRAULIC SAFETY PROCEDURES.
_______
(1)
Obey the hydraulic safety procedures (Ref. TASK 29-00-00-910-002).
(2)
Make sure that the Blue hydraulic system is depressurized and put it in the maintenance configuration (Ref. TASK 29-00-00-864-001).
(3)
Make sure that the reservoir of the Blue hydraulic system is depressurized (Ref. TASK 29-14-00-614-001).
(4)
Make sure that the warning notices are in position to tell persons not to pressurize the Blue hydraulic system:
-in the cockpit on the hydraulic section 40VU of the overhead panel, - on the ground service panel of the Blue hydraulic system.
(5)
Make sure that the safety barriers are in position.
R 1EFF : 001-049, 051-061, 101-105, 201-203, 1 29-22-51Page 478 1 1 Config-1 Aug 01/05 1 1 1CES 1
(6)
Make sure that the RAT is extended (Ref. TASK 29-22-00-869-001).
(7)
Make sure that the container is in position below the RAT.
4. Procedure
_________
(Ref. Fig. 408/TASK 29-22-51-991-010) Subtask 29-22-51-860-067
A. Preparation for Installation
(1)
Clean the component interface and/or the adjacent area.
(2)
Do an inspection of the component interface and/or the adjacent area.
(3)
Make sure that all visible parts of the turbine assy (5) and the leg assembly (7) are tight and correctly locked.
(4)
Make sure that all lockwires and tab washers on the attachment parts of the turbine assy (5) and the leg assembly (7) are in correct condition.
(5)
Apply HYDRAULIC FLUIDS (Material No. 02-003) to the new O-rings (1) and (2).
(6)
Apply COMMON GREASE (Material No. 04-021) to the threads of the studs.
(7)
Install the new O-ring (2) on the spigot of the turbine assy (5).
(8)
Install the new O-ring (1) in the leg assembly (7). Subtask 29-22-51-420-057
B.
Installation of the Turbine Assy of the RAT
(1) Align the holes of the back plate (6) and the studs on the leg assembly (7).
NOTE : Two of the studs are offset.
____
NOTE : Make sure that the turbine assy (5) stays level when you move
____
it on to the drive quill.
(2) Install the turbine assy (5) to the leg asssembly (7).
R 1EFF : 001-049, 051-061, 101-105, 201-203, 1 29-22-51Page 479 1 1 Config-1 Aug 01/05 1 1 1CES 1
(3)
Install the new tab washer (3) and the nuts (4).
(4)
Attach the ADAPTER - TORQUE (DAH600865) to a torque wrench that is
228.6 mm (9.0000 in.) in length.
(5)
Use the torque wrench and the ADAPTER - TORQUE to tighten the nuts (4).
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址：A320飞机维护手册 AMM HYDRAULIC POWER 液压6(29)
