(2)
Loosen the nut (5) and remove the clogging indicator (4).
(3)
Remove and discard the O-rings (2) and the back-up ring (3). Put a blanking plug in the port (1).
1EFF : 001-049, 051-061, 101-105, 201-203, 1 29-22-51Page 456 1 1 Config-1 Aug 01/05R 1 1 1CES 1
Clogging Indicator and Filter Assembly
Figure 407/TASK 29-22-51-991-007
1EFF : 001-049, 051-061, 101-105, 201-203, 1 29-22-51Page 457 1 1 Config-1 Aug 01/05R 1 1 1CES 1
TASK 29-22-51-400-003 Installation of the Clogging Indicator WARNING : PUT THE SAFETY DEVICES AND THE WARNING NOTICES IN POSITION BEFORE YOU
_______ START A TASK ON OR NEAR:
-
THE FLIGHT CONTROLS
-
THE FLIGHT CONTROL SURFACES
-
THE LANDING GEAR AND THE RELATED DOORS
-COMPONENTS THAT MOVE. WARNING : MAKE SURE THAT THE TRAVEL RANGES OF THE FLIGHT CONTROL SURFACES ARE
_______ CLEAR BEFORE YOU PRESSURIZE/DEPRESSURIZE A HYDRAULIC SYSTEM.
WARNING : MAKE SURE THAT THE RAT TRAVEL RANGE IS CLEAR BEFORE YOU
_______ EXTEND/RETRACT THE RAT.
WARNING : MAKE SURE THAT THE GROUND SAFETY-LOCKS ARE IN POSITION ON THE LANDING
_______ GEAR.
1.
Reason for the Job
__________________
Self Explanatory
2.
Job Set-up Information
______________________
A. Fixtures, Tools, Test and Support Equipment
-------------------------------------------------------------------------------REFERENCE QTY DESIGNATION -------------------------------------------------------------------------------
No specific Torque Wrench : range 0.20 to 3.60 m.daN
(2.00 to 26.00 lbf.ft)
B. Consumable Materials
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
No specific lockwire, corrosion-resistant steel dia 0.8 mm (0.0315 in.)
Material No. 02-003 F NSA 307110 TYPE 4 HYDRAULIC FLUID (PHOSPHATE ESTER BASE) (Ref. 20-31-00)
1EFF : 001-049, 051-061, 101-105, 201-203, 1 29-22-51Page 458 1 1 Config-1 Aug 01/05R 1 1 1CES 1
C. Expendable Parts -------------------------------------------------------------------------------
FIG.ITEM --------- |DESIGNATION ---------------------------------------- |IPC-CSN------------------------------
2 O-rings 29-22-51 01 -260
3 back-up ring 29-22-51 01 -270A
D. Referenced Information
------------------REFERENCE -------------------------------DESIGNATION ------------------------------
-------------------------------------------------------------------------------
12-12-29-611-001 Fill the Hydraulic Fluid Reservoir with a Hand Pump 12-12-29-611-002 Fill the Hydraulic Fluid Reservoir with a Hydraulic Service Cart 29-00-00-864-001 Put the Related Hydraulic System in the Depressurized
Configuration before Maintenance Action 29-00-00-910-002 Safety Procedures of the Hydraulic System 29-10-00-863-003 Pressurize the Blue Hydraulic System with a Ground
Power Supply 29-10-00-864-003 Depressurize the Blue Hydraulic System 29-14-00-614-001 Depressurization of the Hydraulic Reservoirs 29-14-00-614-002 Pressurization of the Hydraulic Reservoirs through
the Ground Connector 29-22-00-869-001 Extension of the Ram Air Turbine (RAT) on the Ground 29-22-00-869-002 Retraction of the Ram Air Turbine (RAT) on the Ground 29-22-51-991-007 Fig. 407
3. Job Set-up
__________
Subtask 29-22-51-860-063
A. Aircraft Maintenance Configuration
WARNING : OBEY THE HYDRAULIC SAFETY PROCEDURES.
_______
(1)
Obey the hydraulic safety procedures (Ref. TASK 29-00-00-910-002).
(2)
Make sure that the Blue hydraulic system is depressurized and put it in the maintenance configuration (Ref. TASK 29-00-00-864-001).
(3)
Make sure that the reservoir of the Blue hydraulic system is depressurized (Ref. TASK 29-14-00-614-001).
1EFF : 001-049, 051-061, 101-105, 201-203, 1 29-22-51Page 459 1 1 Config-1 Aug 01/05R 1 1 1CES 1
(4)
Make sure that the warning notices are in position to tell persons not to pressurize the Blue hydraulic system:
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址：A320飞机维护手册 AMM HYDRAULIC POWER 液压6(23)
