曝光台 注意防骗
网曝天猫店富美金盛家居专营店坑蒙拐骗欺诈消费者
28 Pin 27-11-24-01-125 GUN ALL
27-62-71-01-195 GUN ALL
D. Location Zones
Zone Area
133 Main Landing Gear Wheel Well, Body Station 663.75 to Body Station
727.00 - Left
134 Main Landing Gear Wheel Well, Body Station 663.75 to Body Station
727.00 - Right
572 Left Wing - Aileron
672 Right Wing - Aileron
E. Access Panels
Number Name/Location
571DB Lower Outboard Fixed Trailing Edge Access Panel
671DB Lower Outboard Fixed Trailing Edge Access Panel
F. Aileron Wing Installation
SUBTASK 27-11-24-420-001
(1) Install the aileron wing quadrant assembly [9]:
(a) Assemble the aileron wing quadrant assembly [9] if it is necessary:
737-600/700/800/900
AIRCRAFT MAINTENANCE MANUAL
EFFECTIVITY
GUN ALL 27-11-24
Page 409
Oct 10/2007
D633A101-GUN
BOEING PROPRIETARY - Copyright#Unpublished Work - See title page for details
1) Apply sealant, A00247 to the top bearing [40];
2) Roller swage the top bearing [40] (SOPM 20-50-03);
3) Apply compound, C00913 to the bottom bearing [40];
4) Install the bearings [40] and bushing [41] in the aileron wing quadrant assembly [9];
5) Install the bolt [20], washer [21], bushing [22], washer [30], nut [29] and new pin [28] to
connect the aileron wing quadrant assembly [9] with the aileron control rod [17].
(b) Connect the aileron wing quadrant assembly [9] to the aileron hinge support [18].
1) Install the bolt [23], washer [35], bushing [24], washer [25] nut [27] and new pin [26].
(c) Install the bolt [10], washer [11], bushing [12], washer [15], nut [14], and new pin [13] to
connect the aileron control rod [17] to the aileron [16].
(d) Install the bolt [31] and washer [32] to connect the aileron position transmitter rod to the
aileron wing quadrant assembly [9]:
1) Make sure the aileron position transmitter rod is 17.01 inches (432.05 millimeters) from
bolt center to bolt center;
2) If adjustment of the aileron position transmitter rod is necessary, do this task: Aileron
Position Transmitter Installation Test, TASK 31-31-31-700-801.
(e) Put the cable ABSA [2] (for the left wing) and cable ABSB [4] (for the right wing) in the
bottom groove of the aileron wing quadrant assembly [9].
(f) Put the cable ABSB [4] (for the left wing) and cable ABSA [2] (for the right wing) in the top
groove of the aileron wing quadrant assembly [9].
(g) Install the cable terminations through the retaining plates [19].
(h) Install the retaining plates [19] with the bolts [5], washers [6], washers [7] and nuts [8].
(i) Install the cable guard [36] with bolts [37], washers [38] and nuts [39].
1) Adjust the cable guard [36] until the gap between the cable guard [36] and the aileron
wing quadrant assembly [9] is 0.030-0.050 inch (0.76-1.27 millimeters).
(j) Connect the cable ABSA [2] and cable ABSB [4] to the turnbuckles [1], but keep the cable
tension at zero.
SUBTASK 27-11-24-820-001
(2) Adjust the tension of the cable ABSA [2] and cable ABSB [4]. To adjust the cables ABSA [2] and
ABSB [4], do this task: Aileron Cables Adjustment, TASK 27-11-00-820-801.
SUBTASK 27-11-24-860-002
(3) Close these access panels:
(a) On the left wing, close this access panel:
Number Name/Location
571DB Lower Outboard Fixed Trailing Edge Access Panel
(b) On the right wing, close this access panel:
Number Name/Location
671DB Lower Outboard Fixed Trailing Edge Access Panel
SUBTASK 27-11-24-860-003
(4) Do this task: Put the Aileron Hydraulic Systems A and B Back to the Condition Before
Pressure Removal, TASK 27-11-00-860-802.
737-600/700/800/900
AIRCRAFT MAINTENANCE MANUAL
EFFECTIVITY
GUN ALL 27-11-24
Page 410
Feb 10/2006
D633A101-GUN
BOEING PROPRIETARY - Copyright#Unpublished Work - See title page for details
SUBTASK 27-11-24-730-001
(5) Do this task: Aileron Travel Test, TASK 27-11-00-700-809.
------------------------- END OF TASK ---------------------------
737-600/700/800/900
AIRCRAFT MAINTENANCE MANUAL
EFFECTIVITY
GUN ALL 27-11-24
Page 411
Feb 10/2006
D633A101-GUN
BOEING PROPRIETARY - Copyright#Unpublished Work - See title page for details
AILERON BALANCE PANELS - REMOVAL/INSTALLATION
1. General
A. This procedure has these tasks:
(1) A removal of the aileron balance panel
(2) An installation of the aileron balance panel.
B. There are four aileron balance panels on each wing. This procedure is applicable for all the aileron
balance panels.
TASK 27-11-31-000-801
2. Aileron Balance Panels Removal
(Figure 401)
A. References
Reference Title
27-11-00-860-801 Remove Pressure from the Aileron Hydraulic Systems A and B
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址：
737-600/700/800/900 AIRCRAFT MAINTENANCE MANUAL飞机维护手册1(150)
