曝光台 注意防骗
网曝天猫店富美金盛家居专营店坑蒙拐骗欺诈消费者
(a) Remove the pin [82], nut [83], washer [84], bushing [85], washer [88] and bolt [89] to
disconnect the aileron control rod [81] from the aileron [32].
SUBTASK 27-11-00-860-099
(3) Make sure that the Flap Lever is in the up, retracted position.
D. Do a Test of the Aileron Friction and Motion
SUBTASK 27-11-00-720-001
(1) Do a test of the aileron friction and motion:
NOTE: During this test, the force is positive (+) if you need to push the aileron to get it to a
specified position. The force is negative (-) if you need to hold the aileron to keep it at a
specified position.
GUN 101-122
(a) Move the aileron surface to the rig position and release.
NOTE: The aileron rig position is when the outboard edge of the aileron upper surface is
0.49 ±0.03 inch (12.4 ±0.8 millimeters) below the adjacent fixed lower trailing
edge surface (Figure 506).
737-600/700/800/900
AIRCRAFT MAINTENANCE MANUAL
EFFECTIVITY
GUN ALL 27-11-00
Page 544
Oct 10/2007
D633A101-GUN
BOEING PROPRIETARY - Copyright#Unpublished Work - See title page for details
GUN 101-122 (Continued)
GUN 001-099, 155-157, 201-999
(b) Move the aileron surface to the rig position and release.
NOTE: The aileron rig position is when the outboard edge of the aileron upper surface is
0.245 ±0.03 inch (6.2 ±0.8 millimeters) below the adjacent fixed lower trailing
edge surface (Figure 506).
GUN ALL
(c) If the aileron moves away from the rig position, do these steps:
1) Hold the aileron at the rig position with a force scale at 8.75 ±0.50 inches (222.3 ±12.7
millimeters) aft of the hinge centerline and perpendicular to the aileron chord plane.
(held negative (-) force)
2) Slowly apply or relax the force as it is necessary until the aileron moves up and down
from the rig position.
a) Measure the force that is necessary to move the aileron up (up positive (+) force).
b) Measure the force that is necessary to move the aileron down (down positive (+)
force).
3) Add the up force with the down force.
NOTE: Add the forces with the same signs. Subtract forces with the opposite signs.
4) Make sure the total of the two values is not more than 5 pounds (22.2 newtons).
(d) If the aileron does not move away from the rig position, do these steps;
1) Slowly apply a force perpendicular to the aileron chord plane 8.75 ±0.5 inches (222.3
±12.7 millimeters) aft of the hinge centerline.
2) Measure the force that is necessary to move the aileron up (up force).
3) Measure the force that is necessary to move the aileron down (down force).
4) Add the up force with the down force.
NOTE: Add the forces with the same signs. Subtract forces with the opposite signs.
5) Make sure the total of the two forces is not more than 5 pounds (22.2 newtons).
(e) Measure the maximum positive force necessary to move the aileron to these specified
positions:
1) Make sure that the aileron moves smoothly throughout its travel, and that there is no
binding at the aileron hinges and seals.
2) Move the aileron from the rig position to the full down position.
3) Move the aileron from the full down position to the full up position.
4) Move the aileron from the full up position to the rig position.
(f) Make sure the force is not more than 13 pounds (58 newtons) for aileron down.
(g) Make sure the force is not more than 3 pounds for (13 newtons) aileron up.
(h) Measure the aileron travel before the aileron touches the wing structure at the upper and
lower limits of travel.
NOTE: Apply only enough force to maintain contact while you measure the aileron travel.
737-600/700/800/900
AIRCRAFT MAINTENANCE MANUAL
EFFECTIVITY
GUN ALL 27-11-00
Page 545
Oct 10/2007
D633A101-GUN
BOEING PROPRIETARY - Copyright#Unpublished Work - See title page for details
1) Make sure the aileron travels a minimum of 3.67 inches (93.2 millimeters) up before the
aileron touches the structure.
2) Make sure the aileron travels a minimum of 3.15 inches (80.0 millimeters) down before
the aileron touches the structure.
E. Put the Airplane Back to Its Usual Condition
SUBTASK 27-11-00-020-002
(1) Connect the aileron control rod [81] to the aileron [32].
(a) Install the bushing [85], bolt [89], washer [88], washer [84], nut [83], and pin [82] to connect
the aileron control rod [81] to the aileron.
SUBTASK 27-11-00-860-031
(2) Do this task: Put the Aileron Hydraulic Systems A and B Back to the Condition Before
Pressure Removal, TASK 27-11-00-860-802.
------------------------- END OF TASK ---------------------------
737-600/700/800/900
AIRCRAFT MAINTENANCE MANUAL
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址：
737-600/700/800/900 AIRCRAFT MAINTENANCE MANUAL飞机维护手册1(116)
