S 644-013
(7)
Apply grease to the splined male drives of the latch actuator.
S 104-028
(8)
Clean the mating surfaces to make an electrical bond at one of the bolt locations.
S 424-014
(9)
Put the bellcrank (4) in its position to engage the latch actuator (16).
S 424-029
(10)
Install the four bolts, nuts, and washer to attach the latch actuator to the support bracket (17) (View A-A, Fig. 401).
S 764-027
(11)
Use a bonding meter to measure the electrical resistance across the bond (Ref 20-22-01/601).
NOTE: The maximum resistance must not be more than 0.0025 ohms.
____
S 434-015
(12) Connect and install the adjacent latch mechanism parts as follows:
CAUTION:_______BE CAREFUL WHEN YOU INSTALL THE BELLCRANK (7). THE SPLINE TEETH OF THE BELLCRANK CAN CAUSE DAMAGE TO THE FACE OF THE BEARING (15), IF YOU ARE NOT CAREFUL.
(a) Put the adapter (5) in its position on the latch actuator (16).
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
52-34-06
ALL ú ú 01 Page 408 ú Oct 10/91
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400
MAINTENANCE MANUAL
INTERNAL INTERNAL
(M + 15)
MANUAL DRIVE TORQUE
M
TURNS OF MANUAL DRIVE TORQUE WRENCH
NOTE: THE TURNS ARE THE NUMBER OF TURNS OF A TORQUE WRENCH IN THE MANUAL DRIVE. COUNT THE TURNS AFTER YOU FIND THE INTERNAL STOPS.
USE A TORQUE WRENCH TO FIND THE INTERNAL STOPS AS FOLLOWS:
1.
MEASURE THE TORQUE (M) WHILE YOU MANUALLY TURN THE ACTUATOR.
(THE TORQUE SHOULD BE CONSTANT WITHIN |2 POUND-INCHES).
2.
TURN THE ACTUATOR UNTIL THE TORQUE INCREASES BY 15-20 POUND-INCHES (M + 15).
3.
TURN THE ACTUATOR 1/2-TURN IN THE OPPOSITE DIRECTION FROM THE (M + 15) POINT.
4.
THE INTERNAL STOPS ARE AT THIS POINT.
Actuator Internal Stop and Rig Positions
Figure 402
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
52-34-06
ALL ú ú 01 Page 409 ú Oct 10/91
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400
MAINTENANCE MANUAL
(b)
Push the bellcrank (7) in the forward direction, through the bearing (15) to align it with the adapter (5).
(c)
Put the clamp (6) in its position on the adapter (5) and bellcrank (7).
(d)
Install the two bolts, nuts and washer (24, 25, 30 and 31).
(e)
Put clamps (8)(9) in their position on the bellcrank (7), torque tube (13), and double-throw bellcrank (10).
(f)
Install the two bolts, nuts and washer at each clamp.
(g)
Connect the pushrod (14) to the bellcrank (7).
S 824-016
(13)
Adjust the latch mechanism (Ref 52-34-00/501).
S 834-017
(14)
Manually turn the latch actuator to the fully open position.
S 434-018
(15)
Connect the electrical connector (2) at connector P2 to the latch actuator (16).
S 414-019
(16)
Install the lower door lining.
S 864-020
(17)
Remove the DO-NOT-CLOSE tags and close these circuit breakers for the applicable cargo door:
(a)
P59 Aft Equipment Panel
1) AFT CARGO DOOR POWER UNITS
(b)
P414 Power Distribution Center - Left
1) 414A21 LOWER CARGO DOOR FWD
2) 414F15 CARGO DOOR CONTROL FWD
3) 414F16 CARGO DOOR CONTROL AFT
(18)
Close the cargo door.
S 414-021
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
52-34-06 中国航空网 www.aero.cn 航空翻译 www.aviation.cn 本文链接地址：747-400 AMM 飞机维护手册 舱门 DOORS 3(73)
