S 712-024
(13)
Do these steps to do a test of the normal brake system operation:
(a)
Push the brake pedals to the stops and hold them in this position. 1) Do a check for leaks of hydraulic fluid at each brake
bleeder valve.
2) Monitor the indicator on each brake assembly.
3) Make sure that each brake operated to compress the heat
stack.
(b)
Release the brake pedals. 1) Monitor the indicator on each brake assembly. 2) Make sure that each brake is released.
(c)
If a brake did not operate correctly, set the applicable hydraulic fuse again. 1) Get access to the applicable normal antiskid valve module. 2) Hold the fuse handle in the RESET position for 5 seconds
minimum. 3) Do the normal brake operation test again.
S 902-025
(14) If you set a fuse again and the applicable brake does not operate correctly, replace the applicable hydraulic fuse (AMM 32-42-02/201).
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
32-41-00
ALL ú ú 01 Page 212 ú Oct 18/00
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400 MAINTENANCE MANUAL
S 862-026
(15) Remove the pressure from hydraulic system No. 4 (AMM 29-11-00/201).
S 862-051
WARNING: MAKE SURE THAT PERSONS AND EQUIPMENT ARE CLEAR OF ALL CONTROL
_______ SURFACES BEFORE YOU SUPPLY HYDRAULIC POWER. AILERONS, RUDDERS, ELEVATORS, FLAPS, SPOILERS, LANDING GEAR, AND THRUST REVERSERS CAN MOVE QUICKLY WHEN YOU SUPPLY HYDRAULIC POWER. THIS CAN CAUSE INJURY TO PERSONS AND DAMAGE TO EQUIPMENT.
(16)
Pressurize hydraulic system No. 1 or 2 (AMM 29-11-00/201).
S 712-028
(17)
Do these steps to do a test of the alternate brake system operation:
(a)
Push the brake pedals to the stops and hold them in this position. 1) Do a check for leaks of hydraulic fluid at each brake
bleeder valve. 2) Monitor the indicator on each brake assembly. 3) Make sure that each brake operated to compress the heat
stack.
(b)
Release the brake pedals. 1) Monitor the indicator on each brake assembly. 2) Make sure that each brake is released.
(c)
If a brake did not operate correctly, set the applicable hydraulic fuse again. 1) Get access to the applicable alternate antiskid valve
module assembly. 2) Hold the fuse handle in the RESET position for 5 seconds minimum. 3) Do the alternate brake operation test again.
S 902-029
(18)
If you set a fuse again and the applicable brakes do not operate correctly, replace the applicable hydraulic fuse (AMM 32-42-02/201).
H.
Put the Airplane Back to Its Usual Condition
(1)
Set the parking brake.
S 092-052
(2)
Do this task: "Removal of the Door Locks from the Wing Landing Gear" (AMM 32-00-30/201).
S 092-053
(3)
Do this task: "Removal of the Door Locks from the Body Landing Gear" (AMM 32-00-30/201).
S 862-030
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
32-41-00
ALL ú ú 01 Page 213 ú Oct 10/97
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400 MAINTENANCE MANUAL
S 862-032
(4) Remove the hydraulic power if it is not necessary (AMM/29-11-00/201).
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
32-41-00
ALL ú ú 01 Page 214 ú Oct 10/97
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400 MAINTENANCE MANUAL
HYDRAULIC BRAKE SYSTEM - ADJUSTMENT/TEST
________________________________________
1. General_______
A. This procedure has the instructions to do these tasks:
(1)
Alternate Source Selector Valve - Operational Test
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址：747-400 AMM 飞机维护手册 起落架 LANDING GEAR 6(32)
