(2)
Remove the warning notice(s).
(3)
Remove the access platform(s).
(4)
Remove the ground support and maintenance equipment, the special and standard tools and all other items.
1EFF : ALL 1 57-26-00Page 607 1 1 Nov 01/04R 1 1 1CES 1
INTENTIONALLY BLANK
R 1 1
57-26-00Page 608
1 1 Nov 01/04 1 1 1CES 1
TASK 57-26-00-220-001
Special Detailed Inspection of Outer Wing Pylon Forward Attachment Fittings
WARNING : MAKE SURE THAT THE GROUND SAFETY-LOCKS ARE IN POSITION ON THE LANDING
_______ GEAR.
WARNING : PUT THE SAFETY DEVICES AND THE WARNING NOTICES IN POSITION BEFORE YOU
_______ START A TASK ON OR NEAR:
-
THE FLIGHT CONTROLS
-
THE FLIGHT CONTROL SURFACES
-
THE LANDING GEAR AND THE RELATED DOORS
-COMPONENTS THAT MOVE.
1. Reason for the Job
__________________
Refer to the MPD TASK: 572654-01
2. Job Set-up Information
______________________
A. Fixtures, Tools, Test and Support Equipment
-------------------------------------------------------------------------------REFERENCE QTY DESIGNATION
-------------------------------------------------------------------------------
No specific warning notice
No specific access platform 3.0 m (9 ft. 10 in.)
B. Consumable Materials
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
Material No. 11-026 GB DEF-STAN 68-148/1 SOLVENT GENERAL PURPOSE (Ref. 20-31-00) Material No. 19-003 USA AMS 3819 LINT-FREE COTTON CLOTH (Ref. 20-31-00)
1EFF : ALL 1 57-26-00Page 609 1 1 May 01/04R 1 1 1CES 1
C. Referenced Information
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
54-51-17-000-001 Removal of the Pylon-to-Wing Forward Attach Fitting at RIB4 54-51-17-400-001 Installation of Pylon-to-Wing Forward Attach Fitting
at RIB4 NTM 57-26-54 PARTS 4 and 6 ASRM 572600 (for corrective action) 57-26-00-991-002 Fig. 602
3. Job Set-up
__________ Subtask 57-26-00-941-051
A. Safety Precautions
(1) Put a warning notice in the cockpit to tell persons not to start the engine 1(2).
Subtask 57-26-00-010-051
B. Get Access
(1)
Put the access platform below the applicable pylon, zone 521(621).
(2)
Remove the pylon-to-wing forward attachment fitting (Ref. TASK 54-51-17-000-001).
4. Procedure
_________ (Ref. Fig. 602/TASK 57-26-00-991-002) Subtask 57-26-00-110-051
A. Preparation for Inspection
(1) Use a MISCELLANEOUS (Material No. 19-003), made moist with CLEANING AGENTS (Material No. 11-026) to clean the forward attachment fitting of the outer wing pylon, inboard and outboard.
1EFF : ALL 1 57-26-00Page 610 1 1 May 01/04R 1 1 1CES 1
Outer Wing Pylon - Forward Attachment Fittings Figure 602/TASK 57-26-00-991-002
1EFF : 1 1R 1CES ALL 1 11 1 57-26-00 Page 611 May 01/04
Subtask 57-26-00-280-050
B. Inspection
(1) Do a special detailed inspection of the forward attachment fitting of the outer wing pylon, inboard and outboard (Ref. NTM 57-26-54 PARTS 4 and 6).
NOTE : If necessary, refer to the ASRM (Ref. ASRM 572600) for the
____ correct repair procedure. If the defect is not included in this repair, you must request a procedure from Airbus Industrie. ________
5. Close-up
Subtask 57-26-00-410-052
A. Close Access
(1)
Make sure that the work area is clean and clear of tool(s) and other items.
(2)
Install the pylon-to-wing forward attachment fitting (Ref. TASK 54-51-17-400-001).
Subtask 57-26-00-942-052
B. Removal of Equipment
(1)
Remove the warning notice(s).
(2)
Remove the access platform(s).
(3)
Remove the ground support and maintenance equipment, the special and standard tools and all other items.
1EFF : ALL 1 57-26-00Page 612 1 1 May 01/04R 1 1 1CES 1
TASK 57-26-00-200-002
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址：A320飞机维护手册 AMM WINGS 机翼2(18)
