(3)
Use 400 grade wet or dry abrasive paper over an area that overlaps the previous area and remove the 320 grade pattern. Flush the surface with water to remove all debris and dry with a clean MISCELLANEOUS (Material No. 19-003).
(4)
Use 1500 Micro-mesh grade wet or dry abrasive paper over an area that overlaps the previous area and remove the 400 grade pattern. Flush the surface with water to remove all debris and dry with a lint-free cloth.
(5)
Use 1800 Micro-mesh cloth over an area that overlaps the previous area and remove the 1500 grade pattern. Flush the surface with clean water to remove all debris and dry with a lint-free cloth.
(6)
Use 2400 Micro-mesh cloth over an area that overlaps the previous area and remove the 1800 grade pattern. Flush the surface with water to remove all debris and dry with a lint-free cloth.
(7)
Use 3200 Micro-mesh cloth over an area that overlaps the previous area and remove the 2400 grade pattern. Flush the surface with water to remove all debris and dry with a lint-free cloth.
(8)
Use 3600 Micro-mesh cloth over an area that overlaps the previous area and remove the 3200 grade pattern. Flush the surface with water to remove all debris and dry with a lint-free cloth.
(9)
Use 4000 Micro-mesh cloth over an area that overlaps the previous area and remove the 3600 grade pattern. Flush the surface with water to remove all debris and dry with a lint-free cloth.
(10)
Use 6000 Micro-mesh cloth over an area that overlaps the previous area and remove the 4000 grade pattern. Flush the surface with water to remove all debris and dry with a lint-free cloth.
(11)
Measure and record the minimum thickness of the lens. The minimum thickness permitted is 3.33 mm (0.1311 in.).
(12)
The reworked area will have a hazed finish. Remove the haze as follows:
(a) Use the Micro-mesh cotton flannel wipe to apply a sufficient amount of Micro-Gloss and polish until the Micro-Gloss has almost gone.
NOTE : Water can be added to extend the working life of the
____ Micro-Gloss. In warm weather it is recommended to polish the lens in small areas.
(b) Continue to polish with the Micro-Gloss until you get a bright and transparent finish.
(13)
Flush the lens surface with water and dry with a lint-free cloth.
(14)
If you cannot get a satisfactory optical quality by polishing, the glazing panel must be replaced.
5. Close-up
________ Subtask 57-37-12-410-050
A. Close Access
(1)
Make sure that the work area is clean and clear of tool(s) and other items.
(2)
If applicable, install the wing-tip glazing assembly (Ref. TASK 57-37-12-400-001).
Subtask 57-37-12-942-051
B. Removal of Equipment
(1)
Remove the TOOL-ZERO LOCKING, FLAP SLAT CTL LEVER from the flap/slat control lever.
(2)
Remove the access platform(s).
(3)
Remove the warning notice(s).
(4)
Remove the safety barriers.
MISCELLANEOUS (EG : DRAINS) - DESCRIPTION AND OPERATION
_______________________________________________________
1. Component Location
__________________
(Ref. Fig. 001)
A. Wing-Tip Drains
There is a drain-hole in:
- opposite corners of the access panel 534AB (634AB)
-
the bottom of the wing-tip fence
-
the lower surface of the wing tip adjacent to the navigation light. They are used to drain the liquid from the wing-tip.
Wing-Tip Drains
Figure 001
1EFF : ALL 1 57-39-00 Page 2
1 1 Feb 01/98
1 1
1CES 1
MISCELLANEOUS (EG : DRAINS) - INSPECTION/CHECK______________________________________________
R TASK 57-39-00-200-002
R Check of Drain Holes of Wing-tip for Clogging
R WARNING : MAKE SURE THAT THE GROUND SAFETY-LOCKS ARE IN POSITION ON THE LANDING_______
R GEAR.
R WARNING : PUT THE SAFETY DEVICES AND THE WARNING NOTICES IN POSITION BEFORE YOU_______
R START A TASK ON OR NEAR:
R - THE FLIGHT CONTROLS
R - THE FLIGHT CONTROL SURFACES
R - THE LANDING GEAR AND THE RELATED DOORS
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址：A320飞机维护手册 AMM WINGS 机翼2(103)
