_______
GEAR.
WARNING : PUT THE SAFETY DEVICES AND THE WARNING NOTICES IN POSITION BEFORE YOU
_______
START A TASK ON OR NEAR:
-
THE FLIGHT CONTROLS
-
THE FLIGHT CONTROL SURFACES
-
THE LANDING GEAR AND THE RELATED DOORS
-COMPONENTS THAT MOVE.
1.
Reason for the Job
__________________
Self Explanatory
2.
Job Set-up Information
______________________
A. Fixtures, Tools, Test and Support Equipment
-------------------------------------------------------------------------------REFERENCE QTY DESIGNATION -------------------------------------------------------------------------------
No specific adjustable access platform
No specific circuit breaker(s) safety clip(s)
No specific safety barriers
No specific warning notice
98D27803500001 1 TOOL-ZERO LOCKING, FLAP SLAT CTL LEVER
3. Job Set-up
__________
Subtask 57-41-37-941-062
A. Safety Precautions
(1) Put the safety barriers in position.
R (2) Make sure that the TOOL-ZERO LOCKING, FLAP SLAT CTL LEVER
R (98D27803500001) is installed on the flap/slat control lever.
R (3) Put a warning notice in the cockpit to tell persons not to operate
R the slats.
R (4) Put the adjustable access platform in position below the applicable
R pressure-relief panel to be removed.
R Subtask 57-41-37-865-072
R B. Open, safety and tag this(these) circuit breaker(s):
R -------------------------------------------------------------------------------
R PANEL DESIGNATION IDENT. LOCATION
R -------------------------------------------------------------------------------
R 49VU FLIGHT CONTROLS/SLT/CTL AND MONG/SYS1 5CV B06
R 121VU FLIGHT CONTROLS/SLT/CTL/SYS2 7CV R21
R 4. Procedure_________
R Subtask 57-41-37-020-052
R A. Removal of the Pressure-Relief Panels 521AB(621AB), 521CB(621CB),
R 521EB(621EB), 522AB(622AB), 522CB(622CB)
R NOTE : On many of the pressure-relief panels, the screws that retain the____
R panel have different lengths. Make a record of the position of
R each screw as it is removed.
R (1) For the panel 521AB(621AB):
R (a) Hold the panel (1) and remove the screws (2).
R (b) Carefully remove the panel (1).
R (2) For the panel 521CB(621CB):
R (a) Hold the panel (3) and remove the screws (4).
R (b) Carefully remove the panel (3).
R (3) For the panel 521EB(621EB):
R (a) Hold the panel (5). Remove the four screws (6) and the screws
R (7).
R (b) Carefully remove the panel (5).
R (4) For the panel 522AB(622AB):
R (a) Hold the panel (8). Remove the four screws (9) and the screws
R (10).
R (b) Carefully remove the panel (8).
R (5) For the panel 522CB(622CB):
R (a) Hold the panel (11). Remove the screw (12) and the screws (13).
R (b) Carefully remove the panel (11).
TASK 57-41-37-400-002
Installation of the Pressure-Relief Panels 521AB(621AB), 521CB(621CB),
521EB(621EB), 522AB(622AB), 522CB(622CB)
WARNING : MAKE SURE THAT THE GROUND SAFETY-LOCKS ARE IN POSITION ON THE LANDING
_______
GEAR.
WARNING : PUT THE SAFETY DEVICES AND THE WARNING NOTICES IN POSITION BEFORE YOU
_______
START A TASK ON OR NEAR:
-
THE FLIGHT CONTROLS
-
THE FLIGHT CONTROL SURFACES
-
THE LANDING GEAR AND THE RELATED DOORS
-COMPONENTS THAT MOVE.
1. Reason for the Job
__________________
Self Explanatory
2. Job Set-up Information
______________________
A. Fixtures, Tools, Test and Support Equipment
-------------------------------------------------------------------------------REFERENCE QTY DESIGNATION -------------------------------------------------------------------------------
No specific adjustable access platform
No specific non-metallic scraper
No specific safety barriers
No specific warning notice
R No specific Torque Wrench : range 0.00 to 1.20 m.daN 中国航空网 www.aero.cn 航空翻译 www.aviation.cn 本文链接地址：A320飞机维护手册 AMM WINGS 机翼2(131)
