747-400 AMM 飞机维护手册滑油 OIL(103)_航空信息_民用航空_通用航空

曝光台注意防骗网曝天猫店富美金盛家居专营店坑蒙拐骗欺诈消费者

Antigallant Compond Application
Figure 402

G83432
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

79-21-17
ALL ú ú N03 Page 411 ú Oct 10/97
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
////////////////////////A / PW4000 SERIES /747-400 / ENGINES/MAINTENANCE MANUAL ////////////////////////
(k) ENGINES WITH PW SB 72-211; Make sure the center of the forward clamp on the oil trim pressure tube is 2.500 - 3.000 inch (63.500 - 76.200 mm) from the center of the rear clamp.
(l) Tighten the clamp bolts and tubes exactly as follows: 1) Tighten the clamp bolt that attaches the No. 3 bearing oil pressure manifold clamp back to back with the oil trim pressure tube clamp to 36-40 pound-inches (4.1-4.5 newton-meters). 2) Tighten the clamp bolts that attach the tubes to the oil cooler rear bracket to 36-40 pound-inches (4.1-4.5 newton-meters). 3) ENGINES WITHOUT PW SB 79-52; Tighten the clamp bolt (20) that attaches the No. 3 bearing oil strainer (19) to the Flange K bracket (16) to 36-40 pound-inches (4.1-4.5 newton-meters). 4) ENGINES WITH PW SB 79-52; Tighten the bolts that attach the ferrule end of the No. 3 bearing pressure tube to the bracket on Flange K to 36-40 pound-inches (4.1-4.5 newton-meters). 5) Tighten the three bolts that attach the oil trim pressure tube (3) to the main oil filter housing to 85-95 pound-inches (9.6-10.7 newton-meters). 6) Tighten the front tube nut of the No. 3 bearing oil pressure manifold (1) to the strainer housing to 140-160 pound-inches (15.8-18.1 newton-meters), then loosen and tighten again to the same value. 7) Tighten the tube nuts that attach the oil tube metering nipple (2) to 675-750 pound-inches (76.3-84.7 newton-meters). 8) ENGINES WITH PW SB 79-52; Do the steps that follow: a) Install a clamp to the tube nut end of the oil trim pressure tube (3). b) Attach the clamp to a bracket on the secondary flow control valve flange with a bolt, lubricated with Engine Oil, and a nut. c) Tighten the nut to 36-40 pound-inches (4.1-4.5 newton-meters).
9) ENGINES WITHOUT PW SB 79-52; Tighten the No. 3 bearing oil pressure manifold nut to the No. 3 bearing oil strainer (19) at Flange K (16) to 675-750 pound-inches (76.3-84.7 newton-meters).
(m) Attach the lockwire or safety cable and safety cable ferrule at all necessary locations.
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

79-21-17
ALL ú ú N03 Page 412 ú Oct 10/97
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
(n) ENGINES WITHOUT PW SB 79-52; Do the steps that follow: 1) Install the spray shield (14) to the inboard side of the
rear No. 3 bearing oil pressure manifold connection. 2) Attach the spray shield (14) with the hose clamp (13). 3) Tighten the hose clamp (14) to 15-18 pound-inches (1.7-2.0
newton-meters).
(o) ENGINES WITH PW SB 79-52; Do the steps that follow: 1) Install the spray shield (21) to the inboard side of the
rear No. 3 bearing oil pressure manifold (1) that is
attached to the No. 3 bearing pressure tube (15).
2) Attach the spray shield (21) with a clamp and a bolt (28), threads lubricated with Engine Oil, to a bracket attached to the flange of the cooling air tube on the high compressor.
3) Tighten the bolt (28) to 36-40 pound-inches (4.1-4.5 newton-meters).
E. Put airplane back to its initial condition.
S 614-020-N00
(1) Fill the engine oil system (AMM 12-13-01/301).
S 414-021-N00
WARNING: OBEY THE INSTRUCTIONS IN AMM 78-31-00 WHEN YOU CLOSE THE THRUST
_______ REVERSERS. IF YOU DO NOT OBEY THE INSTRUCTIONS, INJURY TO PERSONS OR DAMAGE TO EQUIPMENT COULD OCCUR.
(2)
Close the left thrust reverser (AMM 78-31-00/201).