32-11-02
ALL ú ú 01 Page 208 ú Jun 18/99
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400 MAINTENANCE MANUAL
S 842-026
CAUTION: DO NOT MOVE THE AIRPLANE WHILE THE SHOCK STRUTS ARE NOT
_______ PRESSURIZED. THE SHOCK STRUTS MUST HAVE PRESSURE TO PERMIT MOVEMENT OF THE AIRPLANE. IF THEY DO NOT HAVE PRESSURE, DAMAGE TO THE INNER AND OUTER CYLINDERS WILL OCCUR.
(2) Release the pressure and drain the fluid from the shock strut (AMM 32-11-02/301).
NOTE: It is not necessary to lift the airplane with jacks.
____
S 022-027
(3)
Disconnect the hydraulic tube from the shutoff valve.
S 022-028
(4)
Remove the shutoff valve from the flow fuse.
S 022-029
(5)
Remove the flow fuse from the shock strut.
NOTE: Put a container under the fuse to catch fluid that can fall.
____
TASK 32-11-02-402-025
5. Wing Landing Gear Shock Strut Flow Fuse and Shutoff Valve Installation (Fig.______________________________________________________________________ 201)
A. Consumable Materials
(1)
B00062 Solvent - O-A-51, Acetone
(2)
B00316 Solvent - TT-N-95, Type I
(3)
D00507 Hydraulic Fluid - MIL-H-6083
(4)
D00128 Petrolatum - VV-P-236
B.
References
(1)
AMM 09-11-00/201, Towing
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
32-11-02
ALL ú ú 01 Page 209 ú Jun 18/99
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400
MAINTENANCE MANUAL
(2)
AMM 12-15-03/301, Wing Landing Gear Shock Strut
(3)
AMM 32-00-30/201, Wing Landing Gear Doors
(4)
AIPC 32-11-01 Fig. 5
C.
Access
(1)
Location Zone
735 Wing Landing Gear, LH
745 Wing Landing Gear, RH
D.
Procedure
S 222-111
CAUTION: MAKE SURE THAT YOU DO NOT MOVE OR DAMAGE THE WING GEAR TRUCK
_______ SENSORS OR TARGET BRACKET. IF THE TARGET BRACKET OR SENSORS ARE MOVED, THEN THE AIRPLANE SYSTEMS MAY NOT RECOGNIZE AN IN-AIR CONDITION.
(1) If the sensor or target bracket is moved or damaged, then do the task to measure the wing landing gear truck sensor clearance (AMM 32-61-22/201).
S 112-070
CAUTION: DO NOT USE COMPRESSED AIR OR OTHER PRESSURIZED FLUIDS TO CLEAN
_______ THE FLOW FUSE. IF YOU CLEAN THE FLOW FUSE WITH HIGH PRESSURE, YOU CAN CAUSE DAMAGE TO THE INNER COMPONENTS OF THE FUSE. THIS CAN CAUSE THE FLOW FUSE TO OPERATE INCORRECTLY.
(2)
Clean the flow fuse:
(a)
Flush the flow fuse with acetone.
(b)
Make the flow fuse dry with a clean cloth to remove all signs of the acetone.
(3)
Soak the O-ring with hydraulic fluid.
S 642-105
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
32-11-02
ALL ú ú 01 Page 210 ú Jun 18/99
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400 MAINTENANCE MANUAL
S 432-036
(4) Install the O-ring on the flow fuse.
S 642-037
(5) Apply a light layer of petrolatum on the O-ring.
S 822-038
(6) Make the extension of the pin equal on each side of port A (View A).
NOTE:____ The difference in the extensions must be less than 0.005
inch (0.127 mm).
S 422-039
(7)
Install the flow fuse:
(a)
Put the flow fuse in the port on the shock strut.
(b)
Tighten the flow fuse to 8-13 pound-feet (10.8-17.6 newton-meters).
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址：747-400 AMM 飞机维护手册 起落架 LANDING GEAR 1(90)
