36-12-55
ALL ú ú 01 Page 405 ú Nov 12/01
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
737-300/400/500MAINTENANCE MANUAL
PNEUMATIC DUCT - REMOVAL/INSTALLATION
_____________________________________
1. General_______
A. This procedure contains two tasks. The first task removes the ducts of the pneumatic system. The second task installs the ducts of the pneumatic system.
B. The ducts for the air conditioning, thermal anti-icing and the pneumatics systems are all attached to the airplane with support clamps. The ducts are put together with the V-band clamps. Some of the ducts sections are made to be short in length. This short length is to make allowance for the thermal expansion caused when the hot air flows through the ducts. When the ducts are installed, the systems are not in operation thus the ducts are cold. The ducts must be stressed by the clamps at the duct joints.
C. Some of the V-band clamps are installed in areas where there are control cables. You must be careful you do not cause the clamps to touch the control cables.
D. The bleed air duct for the APU is found in the APU compartment. The bleed air duct is attached to the upper shroud and APU bleed air valve. Refer to AMM 49-52-13/401 for the APU bleed air duct removal/installation procedure.
TASK 36-19-15-004-001
2. Duct Removal (Fig. 401)____________
A. References
(1)
AMM 36-05-00/201, Pneumatic System
(2)
AMM 71-11-04/201, Fan Cowl Panels
(3)
AMM 78-31-00/201, Thrust Reverser System
B. Prepare to Remove the Ducts
S 864-002
(1)
Make sure the applicable engine is not in operation.
S 864-003
(2)
Put the forward thrust lever in the fully rearward position and attach a DO-NOT-OPERATE tag.
S 864-004
(3)
Put the start lever in the CUTOFF position and attach a DO-NOT-OPERATE tag.
(4)
Remove the pressure from the pneumatic system (AMM 36-05-00/201).
S 864-006
(5)
Put all of the BLEED switches to the OFF position and attach a DO-NOT-OPERATE tag.
S 014-007
(6)
Do the necessary steps that follow to get access to the ducts:
S 864-005
(a) Remove the applicable access panels.
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
36-19-15
ALL ú ú 01 Page 401 ú Nov 12/01
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
737-300/400/500MAINTENANCE MANUAL
V-BAND CLAMP
SEE C
SEE A
DUCT SUPPORT
CLAMP
DUCT SECTION
DUCT SECTION
DUCT SUPPORT BRACKET
SEE B
V-BAND CLAMP
FLANGE DUCT
A
REVERSE CLAMP
CONTROL CABLE OR LINE POSITION IF
(FUEL, HYDRAULIC, ETC.) (REF) NECESSARY
30`
FIXED POSITION DUCT SUPPORT CLAMP 15`
B
(HORIZONTAL)
15`
SUGGESTED BOLT LOCATION
V-BAND CLAMP SPECIAL INSTALLATION
C
Typical Duct Section Installation
Figure 401 (Sheet 1)
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
36-19-15
ALL ú ú 01 Page 402 ú Nov 15/87
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A 737-300/400/500MAINTENANCE MANUAL
DUCT SUPPORT LINK
RIGID DUCT SUPPORT
Typical Duct Section Installation
Figure 401 (Sheet 2)
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
36-19-15
ALL ú ú 01 Page 403 ú Oct 25/85
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A 737-300/400/500MAINTENANCE MANUAL
. 10-12 IN-LBS ABOVE MINIMUM SELF-LOCKING TORQUE FOR DUCT 69-38626-1 . 18-22 IN-LBS ABOVE MINIMUM SELF-LOCKING TORQUE FOR DUCT 69-38626-4 .13-15 IN-LBS ABOVE MINIMUM SELF-LOCKING TORQUE FOR DUCT 69-38625-()
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址：737-300 400 500 AMM 飞机维护手册 PNEUMATIC(109)
