_____________________________________________________
TASK 36-13-41-000-001
Removal of the HP Ground Connector (7300HM)
WARNING : MAKE SURE THAT THE PNEUMATIC SYSTEM IS DEPRESSURIZED BEFORE YOU START
_______
WORK ON THE PNEUMATIC SYSTEM.
1.
Reason for the Job
__________________
Self Explanatory
2.
Job Set-up Information
______________________
A. Fixtures, Tools, Test and Support Equipment
-------------------------------------------------------------------------------
REFERENCE QTY DESIGNATION
-------------------------------------------------------------------------------
No specific blanking cap
No specific circuit breaker(s) safety clip(s)
No specific warning notices
No specific access platform 1.8 m (5 ft. 11 in.)
B. Referenced Information
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
**ON A/C 001-049, 051-099, 101-105, 151-199, 201-210,
36-13-41-991-001 Fig. 401 R **ON A/C 106-149, 211-299, 301-399, 401-499,
36-13-41-991-001-A Fig. 401A **ON A/C ALL
3. Job Set-up
__________
Subtask 36-13-41-865-050
A. Open, safety and tag this(these) circuit breaker(s):
-------------------------------------------------------------------------------PANEL DESIGNATION IDENT. LOCATION -------------------------------------------------------------------------------49VU AIR BLEED/X FEED/VALVE/BAT 2HV D13 49VU AIR BLEED/ENG 1/CTL 3HA1 D12 49VU AIR BLEED/ENG 1/MONG 2HA1 D11 122VU AIR BLEED/ENG 2/CTL 3HA2 Z23 122VU AIR BLEED/ENG 2/MONG 2HA2 Z22 122VU AIR BLEED/X FEED VALVE/NORM 1HV Z20
Subtask 36-13-41-860-050
B. Aircraft Maintenance Configuration
(1) Put the warning notices in position:
-
in the cockpit on the Engine Control Panel 115VU to tell persons not to start the engine(s),
-
in the cockpit on the AIR COND Overhead Control Panel 30VU to tell persons not to push in the APU BLEED pushbutton switch.
(2) Put the access platform in position below access panel 191BB.
Subtask 36-13-41-010-050
C. Remove the access panel 191BB.
4. Procedure
_________
**ON A/C 001-049, 051-099, 101-105, 151-199, 201-210,
(Ref. Fig. 401/TASK 36-13-41-991-001) R **ON A/C 106-149, 211-299, 301-399, 401-499,
(Ref. Fig. 401A/TASK 36-13-41-991-001-A)
HP Ground Connector 7300HM
Figure 401/TASK 36-13-41-991-001
R 1EFF : 001-049, 051-099, 101-105, 151-199, 1 36-13-41Page 403 1201-210, 1May 01/05 1 1 1CES 1
HP Ground Connector 7300HM
Figure 401A/TASK 36-13-41-991-001-A
R 1EFF : 106-149, 211-299, 301-399, 401-499, 1 36-13-41Page 404 1 1 Aug 01/05 1 1 1CES 1
R **ON A/C ALL
Subtask 36-13-41-020-050
A. Removal of the HP Ground Connector
(1)
Hold the HP Ground Connector (3) and remove the eight nuts (1) and the washers (2).
(2)
Discard the nuts (1) and the washers (2).
(3)
Remove the HP Ground Connector (3) and the sealing ring (6).
(4)
Remove the check valve (5) and the sealing ring (4) from the HP Ground Connector (3).
(5)
Put the blanking cap in the open end of the duct.
TASK 36-13-41-400-001
Installation of the HP Ground Connector (7300HM)
WARNING : MAKE SURE THAT THE PNEUMATIC SYSTEM IS DEPRESSURIZED BEFORE YOU START
_______
WORK ON THE PNEUMATIC SYSTEM.
1.
Reason for the Job
__________________
Self Explanatory
2.
Job Set-up Information
______________________
A. Fixtures, Tools, Test and Support Equipment
-------------------------------------------------------------------------------REFERENCE QTY DESIGNATION -------------------------------------------------------------------------------
No specific warning notices
No specific access platform 1.8 m (5 ft. 11 in.)
No specific Torque Wrench : range 0.00 to 1.20 m.daN
(0.00 to 9.00 lbf.ft)
B. Referenced Information
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址：A320飞机维护手册 AMM PNEUMATIC 气源 2(98)
