R No specific 1 ACCESS PLATFORM 2M (6 FT) R No specific 1 ACCESS PLATFORM 3M (10 FT)
B. Consumable Materials
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
Material No. 04-007 USA MIL-M-7866
MOLYBDENUM DISULFIDE POWDER (Ref. 20-31-00)
C. Referenced Information
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
20-26-00-910-002 Installation of Expansion Joints 20-28-00-912-006 Electrical Bonding of Pipes 25-55-11-000-001 Removal of the AFT Cargo-Compartment Partition FR47 25-55-11-400-001 Installation of the AFT Cargo-Compartment Partition
FR47 25-55-12-000-001 Removal of the AFT Cargo Compartment Partition FR65 25-55-12-400-001 Installation of the AFT Cargo Compartment Partition
FR65 28-11-27-400-001 Installation of the Additional Center Tank (ACT)
R 36-12-00-790-001 Leak Test of the APU Bleed-Air Supply-System 36-22-17-400-001 Installation of the APU Overheat Sensing-Elements 52-30-00-860-001 Open the FWD or AFT Cargo-Compartment Door with the
Yellow Electric Pump 52-30-00-860-002 Close the FWD or AFT Cargo-Compartment Door with the
Yellow Electric Pump
36-12-41-991-001 Fig. 401
36-12-41-991-002 Fig. 402
36-12-41-991-015 Fig. 403
3. Job Set-up
__________
**ON A/C 001-049, 051-099, 101-149, 201-299,
Subtask 36-12-41-860-050
A. Aircraft Maintenance Configuration
(1) Make sure that the warning notices are in position:
-
in the cockpit on the Engine Control Panel 115VU to tell persons not to start the engine(s),
-
in the cockpit on the AIR COND Overhead Control Panel 30VU to tell persons not to push in the APU BLEED pushbutton switch,
- on the HP ground connector to tell persons not to pressurize the pneumatic system.
(2) Make sure that the applicable access panels are removed:
(a)
For the APU bleed-air ducts between FR35 and FR36:
-Make sure that the access panels 191BB and 191EB are removed.
(b)
For the APU bleed-air ducts between FR36 and FR42:
-Make sure that the access panel 191JB is removed.
(c)
For the APU bleed-air ducts between FR42 and FR50:
-Make sure that the access panels 147AB, 147EB, 147FB and 197BB are removed.
(d)
For the APU bleed-air ducts between FR46 and FR70:
-Make sure that the AFT cargo compartment door is open
(Ref. TASK 52-30-00-860-001).
(e)
For the APU bleed-air ducts between the FR46 and FR47:
-Make sure that the partition panel 151BW is removed (Ref. TASK 25-55-11-000-001).
(f)
For the APU bleed-air ducts between the FR47 and FR49:
-Make sure that the access panel 151CW is removed.
(g)
For the APU bleed-air ducts between the FR49 and FR52:
-Make sure that the access panel 151DW is removed.
(h)
For the APU bleed-air ducts between the FR52 and FR55:
-Make sure that the access panel 151EW is removed.
(i)
For the APU bleed-air ducts between the FR55 and FR58:
-Make sure that the access panel 151HW is removed.
(j)
For the APU bleed-air ducts between the FR58 and FR59:
-Make sure that the access panel 151JW is removed.
(k)
For the APU bleed-air ducts between the FR59 and FR62:
-Make sure that the access panel 161AW is removed.
(l)
For the APU bleed-air ducts between the FR62 and FR63:
-Make sure that the access panel 161BW is removed.
(m)
For the APU bleed-air ducts between the FR63 and FR65:
-Make sure that the access panel 161CW is removed.
(n)
For the APU bleed-air ducts between the FR65 and FR70:
-Make sure that the partition panel 161DW is removed (Ref. TASK 25-55-12-000-001).
(o)
For the APU bleed-air ducts between the FR70 and FR77:
-Make sure that the access door 312AR is open.
1EFF : 001-049, 051-099, 101-149, 201-299, 1 36-12-41Page 414 1 1 Aug 01/05R 1 1 1CES 1
(p) For the APU bleed-air ducts aft of FR77:
-Make sure that the access door 314AR is open.
(3) Make sure that the access platform is in position below the applicable access panel.
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址：A320飞机维护手册 AMM PNEUMATIC 气源 2(78)
