曝光台 注意防骗
网曝天猫店富美金盛家居专营店坑蒙拐骗欺诈消费者
(d) Move the sprocket [32] and chain [31] up from the bottom of the control stand.
1) Put the sprocket [32] on the splined end of the shaft [27].
2) Move the shaft through the sprocket.
(e) Put the bushing [33] on the splined end of the shaft [27].
1) Move the shaft through the bushing.
(f) Move the shaft [27] through the bearing [34] until the end is moved out through the short
shaft [37].
(g) Install the bearing [28] on the left side of the shaft.
(h) Install the clamp-up bushing [36] on the right side of the stabilizer trim shaft [27].
(i) Install the bearing [35] on the right side of the shaft [27].
(j) Lightly tap the shaft [27] from the left side.
NOTE: Do this step to make sure that the assembled parts are tight and in the correct
position.
SUBTASK 27-62-22-420-005
(3) Do these steps to activate and adjust the stabilizer trim assembly:
(a) Remove the temporary wire tie from the chain [31] and sprocket [32].
(b) To adjust the stabilizer control chain, do this task: Stabilizer Control Cable and Chain
Adjustment, TASK 27-41-00-820-801.
SUBTASK 27-62-22-410-001
(4) Do these steps to connect the flap lever syncro assembly (Figure 401):
(a) Put the link assembly [20] in the clevis for the flap lever position syncro assembly.
(b) Install the nut [18] and the bolt [19].
737-600/700/800/900
AIRCRAFT MAINTENANCE MANUAL
EFFECTIVITY
GUN ALL 27-62-22
Page 420
Jun 10/2007
D633A101-GUN
BOEING PROPRIETARY - Copyright#Unpublished Work - See title page for details
SUBTASK 27-62-22-410-007
(5) Do this step to connect the flap indicator assembly:
(a) Install the bolt [17], washer [15], washer [14], and nut [16] in the link assembly [13] and
indicator assembly arm.
SUBTASK 27-62-22-040-006
(6) Do these steps to activate the speed brake lever:
(a) Go into the access area under the forward flight compartment floor.
1) Remove the rig pin from the rig pin kit, SPL-1585 from the forward drum of the speed
brake assembly.
2) Do this task: Speed Brake Control Lever Adjustment, TASK 27-62-00-820-801.
SUBTASK 27-62-22-420-006
(7) Install these covers on the control stand.
(a) Install the upper left cover [12].
1) Install the three screws [50].
(b) Install the upper right cover [21].
1) Install the three screws [51].
SUBTASK 27-62-22-010-007
(8) Install the control stand access covers:
(a) The left upper side panel [1].
1) Attach with four screws [2].
(b) The left lower side panel [5]:
1) Attach with five screws [2]
(c) The right upper side panel [3]:
1) Attach with four screws [2].
(d) The right lower side panel [4]:
1) Attach with four screws [2].
SUBTASK 27-62-22-420-007
(9) Install the stabilizer trim wheel assemblies:
(a) Install the right stabilizer trim wheel [7].
1) Install the right bolt [8].
2) Tighten the bolt [8] to 150 in-lb (16.9 Nm) - 170 in-lb (19.2 Nm)
(b) Install the left stabilizer trim wheel [11]:
1) Set the crank of the left stabilizer trim wheel [11] 75 to 105 degrees away from the
setting of the crank on the right wheel.
NOTE: This can be set in either direction.
2) Install the left bolt [8].
3) Tighten the bolt [8] to 150 in-lb (16.9 Nm) - 170 in-lb (19.2 Nm).
SUBTASK 27-62-22-200-001
(10) Do a visual check of the assembly:
(a) Move each control through its usual range.
737-600/700/800/900
AIRCRAFT MAINTENANCE MANUAL
EFFECTIVITY
GUN ALL 27-62-22
Page 421
Jun 10/2007
D633A101-GUN
BOEING PROPRIETARY - Copyright#Unpublished Work - See title page for details
(b) Make sure that the electrical bundles do not touch parts.
SUBTASK 27-62-22-410-002
(11) Do these steps to install the switch panel [10] for the trim stabilizer.
(a) Put the panel [10] on the control stand.
(b) Install the four screws [9].
SUBTASK 27-62-22-700-001
(12) Do this task: Thrust Lever Angle Resolver Adjustment, TASK 76-11-05-820-801-F00.
SUBTASK 27-62-22-410-003
(13) Install these covers and stops (Covers and Stops Installation, TASK 76-11-03-400-804-F00).
(a) The left side cover.
(b) The right cover.
(c) The forward thrust stop and the aft thrust stop.
(d) The knob [6] for the stabilizer trim horn cutout switch.
SUBTASK 27-62-22-410-004
(14) Install these seals and retainers (Seals, Spacers and Retainer Installation,
TASK 76-11-03-400-802-F00).
(a) The right seal retainer and the right seal.
(b) The left seal retainer and left seal.
SUBTASK 27-62-22-410-005
(15) Install these lightplates (Lightplate Installation, TASK 76-11-03-420-801-F00).
(a) The first officer’s stabilizer trim lightplate.
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址：
737-600-700-800-900 飞机维护手册7 AIRCRAFT MAINTENANCE MANUA(3)
