R Locking Procedure for Circular Connectors - Typical Lockwiring Procedure Figure 002
20-51-12 Page 320-51-12 Page 4
R - Insert the wire end through the appropriate hole (Ref. STEP 3).
R - Twist the lockwire with the locking pliers at a distance of 15 mm
R (0.5905 in.) (Ref. STEP 4).
R - Cut the excessive length (Ref. STEP 5).
R - Bend back the part of the lockwire that is out (Ref. STEP 6).
- Check that the connector is correctly safetied.
R
R (4) Example of Lockwiring
R Miscellaneous lockwiring cases exit, some of them are given in the
R following figures.
(Ref. Fig. 003, 004)
R Locking Procedure for Circular Connectors - Examples of Lockwiring Figure 003
20-51-12 Page 5
R Locking Procedure for Circular Connectors - Examples of Lockwiring Figure 004
20-51-12 Page 620-51-12 Page 7
R B. Locking With an Adhesive Product procedure
R (1) Material
R Adhesive (Mat. No. 08-048).
R (2) Procedure
R
R - Apply the adhesive product on the screwed part of the connector.
R - Screw the connector on the connecting part.
R - Remove the excess adhesive product.
R ______________________3. Locking Type Selection
R The locking type to be applied or not depends on the connector type.
R Refer to the following figures to select the locking type to be applied.
R
(Ref. Fig. 005, 006, 007, 008, 009, 010, 011, 012)
R
R Locking Procedure for Circular Connectors - Locking Type Selection R Pressure Seal E0073
Figure 005
20-51-12 Page 8
R Locking Procedure for Circular Connectors - Locking Type Selection R Connector NAS1599 and Derivative (Screw Locking)
Figure 006
20-51-12 Page 9
R Locking Procedure for Circular Connectors - Locking Type Selection R Connector NSA1599 and Derivative (Bayonet Locking) Figure 007
20-51-12 Page 10
R Locking Procedure for Circular Connectors - Locking Type Selection R Connector MIL-C-5015 R Figure 008
20-51-12 Page 11
R Locking Procedure for Circular Connectors - Locking Type Selection R Connector MIL-C-83723 (Screw Locking) R Figure 009
20-51-12 Page 12
R Locking Procedure for Circular Connectors - Locking Type Selection R Connector EN2997 R Figure 010
20-51-12 Page 13
R Locking Procedure for Circular Connectors - Locking Type Selection R Connector NSA938027 and NSA938028 (MIL-C-38999) R Figure 011
20-51-12 Page 14
R Locking Procedure for Circular Connectors - Locking Type Selection R ABS0327
Figure 012
20-51-12 Page 15
_________________________________________________________________
LOCKING PROCEDURE FOR TERMINAL BLOCKS - DESCRIPTION AND OPERATION
_______
1. General This chapter gives the method used to lock terminal blocks at the end clamps. This process must be applied on all the terminal block end clamps located in the vibration areas.
R __________________2. Standard Procedure
A. Lockwiring procedure
(1) Material Locking pliers Ref. BELZER VAN EXTRA 2855 or equivalent. Lockwire stainless steel 0.6 mm (0.0236 in.) dia. (Mat. 19-018). Lockwire 0.5 mm (0.0196 in.) (AMS 5687) (Mat. 19-009). Lockwire 0.8 mm (0.0314 in.) (Mat. 19-010).
(2) Procedure R (Ref. Fig. 001, 002)
-Install the end clamp on the rail.
-Tighten the assembly with a screwdriver (no specific).
-Insert the lockwire through the screw lockwire hole (Ref. STEP 1).
-Twist the lockwire with the locking pliers at a sufficient length (Ref. STEP 2).
-Insert the wire end through the appropriate hole (Ref. STEP 3).
-Twist the lockwire with the locking pliers at a distance of 15 mm (0.5905 in.) (Ref. STEP 4).
-Cut the excessive length of wire.
-Bend back the part of the lockwire that is out (Ref. STEP 5).
-Check that the end clamp is correctly safetied.
20-51-15 Page 1
Locking Procedure for Terminal Blocks - End Clamp Lockwiring Procedure
NSA937901-S
Figure 001
20-51-15 Page 2
Locking Procedure for Terminal Blocks - End Clamp Lockwiring Procedure
NSA937901-S
Figure 002
20-51-15 Page 320-51-30 Page 1
_______________________________________________SOLDERING PROCESSES - DESCRIPTION AND OPERATION
_______1. General
This chapter gives the general processes for the repair or replacement of
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址：A320 ESPM Electrical Standard Practices Manual 4(57)
