R Terminal Lugs - Stripping and Crimping Tools DAN387 Plug Figure 011
20-48-14 Page 1920-48-14 Page 2020-48-14 Page 21
R (b) Extraction
R _1 Only for ABS0374B:
R - Engage AMP tool 724659-1 at the rear of terminal and push
R up.
R - Extract the housing and the tool from the terminal.
R _2 Only for DAN387-02:
- Engage a screwdriver under the terminal at the front, and
push up.
R - Then pull lightly on the cable to remove the terminal from
R the housing.
R (5) Installation/Removal of the terminal
R (Ref. Fig. 007)
R ________________________________7. E0256 Clip terminal with housing
A. P/N Identification
R R R R R R R R R (1) Terminal E0256 C 1 B N 1 | | | | | | | | | | | --------- Packaging code | 0 = in strip | | | | | | 1 = in bulk | | | | ------------- Nickel plated | | | ----------------- Brass | | --------------------- Size code | ----------------------- Type code : C = Terminal ----------------------------- Standard P/N
R R R R R R R (2) Sleeve E0256 M 1 A 1 | | | | | | | | | -------------- White colored | | | ------------------ Self-extinguishing material | | ---------------------- Size code | ------------------------ Type code : M = Housing ------------------------------ Standard P/N
B. P/N Characteristics
(1) Temperature Minimum operating temperature is -55 deg.C (-67.00 deg.F) Maximum operating temperature is 105 deg.C (221.00 deg.F)
____NOTE : If this terminal is not available, you can replace it by DAN387 with related tools.
R C. Connection Procedure (Ref. Fig. 012)
R (1) Wire stripping Strip the wire to the length A with the applicable tool.
R (2) Crimping procedure (Ref. Fig. 004, 005) - Make sure that the tool is adjusted correctly. - Hold the tool by the fixed handle with the crimping head up. - Push the operating lever out to increase the gap between the barrel and the indenter. - Engage the terminal into the tool and release the lever.
R Terminal Lugs - Stripping, Insertion and Crimping Tools E0256
R Figure 012
20-48-14 Page 2220-48-14 Page 23
____NOTE : Lightly close the rear tabs of the terminal with your fingers to get a better position of the terminal in the indenter.
- Pull the lever in to engage the ratchet in the first notch. - Engage the wire into the rear part of the terminal and make sure that it is in the correct position for crimping.
____NOTE : For Gauge 24 wires, fold the conductor in the middle of the stripped length
____NOTE : For Gauge 24 and Gauge 22 wires, put the wire to one side (not in the middle) of the rear part of the terminal.
- Fully close the tool handles until the ratchet releases. - Release the mobile handle and push the lever to release the terminal.
R R R (3) Insertion/Extraction of the housing (E0256M) (Ref. Fig. 006) - Put the rear part of the protection sleeve(large hole)in front of the terminal. - Manually engage the terminal into the sleeve (for a terminal crimped with a Gauge 24 wire, the operation is easier if you use a CANNON CK1 tool).
R R R (4) Insertion/Extraction of the terminal - Push to insert the terminal and pull to extract it.
___________________________________________________
MISCELLANEOUS TERMINALS - DESCRIPTION AND OPERATION
_______1. General
Miscellaneous terminals installed on aircraft have the following code:
R - E0296 ground pick-up terminal
R - ABS0593 spring spade terminal
R - DAN417 non-insulated terminal
NSA936502 non-insulated TB terminal
R ______________________________2. E0296 Ground Pick-Up Terminals
R
R A. P/N identification
E0296 -01
| |
| -------- Reference Designator
|
---------------- Standard P/N
R
R B. P/N characteristics
R (Ref. Fig. 001)
Used with E0295 connector.
R _____________________________3. ABS0593 Spring Spade Terminal
R
R A. P/N identification
ABS0593 -01
| |
| -------- Size Code
|
------------------- Standard P/N
R
R B. P/N characteristics
R
R (Ref. Fig. 002)
R
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址：A320 ESPM Electrical Standard Practices Manual 4(23)
