Coaxial Contacts - P/N Characteristics CANNON and SOURIAU E0178 R Figure 009
20-48-31 Page 15
Coaxial Contacts - P/N Characteristics RADIALL E0178 R Figure 010
20-48-31 Page 16
R Coaxial Contacts - Wire Stripping CANNON E0178
R Figure 011
20-48-31 Page 17
Coaxial Contacts - Wire Stripping and Crimping Tools RADIALL E0178 R Figure 012
20-48-31 Page 18
R Coaxial Contacts - Wire Stripping and Crimping Tools SOURIAU E0178
R Figure 013
20-48-31 Page 19
Coaxial Contacts - Wire Stripping and Crimping Tools RADIALL E0178 R Figure 014
20-48-31 Page 2020-48-31 Page 21
(m) TORQUE the threaded cap (1) to between 0.5 m.daN (44.2477 lbf.in) and 0.62 m.daN (54.8672 lbf.in)
R R R (n) Put a mark with a red pencil line on the threaded cap (1) and the body (5).
R (2) SOURIAU (Ref. Fig. 013)
R R (a) Install the threaded cap (1) , the washer (2) and the seal (10) on the cable.
R (b) Strip the cable at dimension A.
R (c) Install the braid support (3) against the insulation (4) of the cable (Except for contact E0178-02).
(d) Put the braided shield (5) on the braid support (3).
R (e) Strip the wire at dimension B.
(f) Install the contact core (6) on the stripped wire: For contact Type 01-02 : solder the contact core (6) on the wire For contact Type 03-04 : crimp the contact core (6) wire with tool, do not forget the positioner.
(g) Install the dielectric (8) and the spacer (7) in the contact body (9).
(h) Install the contact body (9) on the contact core (6).
R R (i) Torque the threaded cap (1) to 0.54 m.daN (47.7876 lbf.in) in the contact body (9).
R R (j) Put a mark with a red pencil line on the threaded cap (1) and the contact body (9).
R (3) RADIALL Type 01 and 02 (Ref. Fig. 012)
(a) Strip the cable at the size A.
(b) Install the threaded cap (1) the washer (2) and the seal (1) on the cable.
(c)
Engage the braid support (4) on the braided shield (5).
(d)
Move the braided shield (5) backwards on the braid support (4).
(e)
Strip the wire at the size C.
(f)
Check the size B.
(g)
Engage the stripped wire in the contact core (7).
(h)
Solder the contact core (7) on the stripped wire.
(i)
Install the body (6) on the core contact (7).
(j)
Screw the threaded cap (1) on the body (6) to 0.575 m.daN (50.8849 lbf.in).
(k)
After torquing, mark a pencil red line on the threaded cap (1) and the contact body (6).
(4) RADIALL Type 03 and 04 R (Ref. Fig. 014)
(a)
Strip the cable at the size A and B.
(b)
Install the heat-shrinkable sleeve (1) and the ferrule (2) on the cable.
(c)
Install the threaded cap (3) on the braid support (4).
(d)
Put the braid support (4) in position with the braided shield (5) over the braid support (4).
(e)
Put the ferrule (2) on the braided shield (5) to get the size C.
(f)
Install the washer (6) in the stripped wire.
(g)
Engage the stripped wire in the contact core (7).
(h)
Crimp the contact core (7) on the stripped wire with tool.
(i)
Install the contact body (8) on the contact core (7).
(j)
Screw the threaded cap (3) on the body (8).
(k)
TORQUE the threaded cap (3) to 0.37 m.daN (32.7433 lbf.in) .
(l)
After torquing, mark a pencil red line on the threaded cap (3) and the body (8).
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址：A320 ESPM Electrical Standard Practices Manual 4(44)
