(6)
Fully close the tool handles until the safety ratchet releases.
(7)
Remove the crimped inner contact.
(8)
Slightly expand the braid (outer conductor).
(9)
Slide the contact body onto the inner contact and under the expanded braid.
20-48-32 Page 47
R Coaxial Contacts - P/N Characteristics, Insertion/Extraction Tools R MIL-C-39029/55-344
Figure 029
20-48-32 Page 48
R Coaxial Contacts - Wire Stripping and Crimping Tools R MIL-C-39029/55-344
Figure 030
20-48-32 Page 49
(10)
Push the center contact until it is locked in position in the contact body. Pull lightly on the cable to make sure that the inner contact is securely locked in position.
(11)
Slide the crimping ferrule forward over the braid and up against the contact body.
(12)
Insert the contact in the applicable crimping tool and crimp on the ferrule and the contact.
____
NOTE : Make sure that the cable, contact and ferrule remain in the correct position during the crimping process.
(13) Slide the sleeve under the crimped ferrule and toward the contact body.
20-48-32 Page 5020-48-33 Page 1
____________________________________________________________________COAXIAL CONTACTS FOR NAS 1599 CONNECTORS - DESCRIPTION AND OPERATION
R R R R _______1. General This chapter gives the connection procedure for coaxial contacts used with NAS1599 and MIL-C5015 connectors.These contacts have the following codes: - NSA938171 and NSA938172
R _________________________________________________________________2. Connection Procedure for Coaxial Contacts NSA938171 and NSA938172
A. Contacts P/N and Characteristics (Ref. Fig. 001) ---------------------------------------------------------------------
R R | | USE WITH | | CONTACTS |------------------------------------------------| | | PLUG | RECEPTACLE | |------------------|-------------------------|----------------------| | | | ABS0498 | | ABS0497 | E0040 | | | E0039 | E0041 | | NSA938171 | E0052 | E0053 | | | NSA938000 | E0054 | | | SOURIAU 8915-21 | NSA938001 | | | SOURIAU 8915-61 | NSA938002 | |------------------|-------------------------|----------------------| | NSA938172 | SOURIAU 8525 | --| ---------------------------------------------------------------------
B. Contacts Insertion / Extraction Tools (Ref. Fig. 002)
C. Wire Stripping (Ref. Fig. 002) Engage the ferrule on the wire. Strip the shield of the wire in order to get the dimension A. Cut the shield in order to get the dimension C. Flare the shield. Strip the conductor in order to get the dimension B.
D. Crimping Procedure and Tools (Ref. Fig. 003)
(1) Engage the insulation sleeve on the stripped portion on the conductor until it comes into contact with the insulation.
(2) Engage the stripped end of the conductor into the contact barrel.
(3) Make sure that : - the rear of the contact comes against the insulating sleeve, - you can see the conductor through the hole in the contact barrel.
(4) Install the contact barrel in the positioner of the conductor crimping tool.
Coaxial Contacts - P/N Characteristics
NSA938171 and NSA938172
Figure 001
20-48-33 Page 2
Coaxial Contacts - Insertion/Extraction and Stripping Tools
NSA938171 and NSA938172
Figure 002
20-48-33 Page 3
R Coaxial Contacts - Crimping Tools NSA938171 and NSA938172 Figure 003
20-48-33 Page 4
(5)
Fully close the tool handles until the safety ratchet releases.
(6)
Remove the crimped contact.
(7)
Engage the contact into the ground until the front part of the contacts are at the same level.
(8)
Move the conductor shield over the rear section of the ground contact.
(9)
Make sure that :
-the shield is in the correct position on the ground contact periphery,
-no shield fiber has gone into the interior of the contact.
(10)
Bring the ferrule against the ground contact shoulder.
(11)
Put the contact in the positioner of the ferrule crimping tool.
(12)
Fully close the tool until the safety ratchet releases.
20-48-33 Page 5
________________________________________________________________
COAXIAL CONTACTS FOR PREN CONNECTORS - DESCRIPTION AND OPERATION
_______
1. General The coaxial contacts for EN3545 connectors installed on aircraft have the codes that follow:
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址：A320 ESPM Electrical Standard Practices Manual 4(51)
