Normal Contacts - P/N Characteristics E0445, E0446, EN3155-004 and EN3155-005 R Figure 007
20-48-24 Page 10
Normal Contacts - Insertion/Extraction Tools E0445, E0446, EN3155-004 and EN3155-005 R Figure 008
20-48-24 Page 11
Normal Contacts - Wire Stripping and Tools E0445, E0446, EN3155-004 and EN3155-005 R Figure 009
20-48-24 Page 12
Normal Contacts - Sleeve Allocation E0445, E0446, EN3155-004 and EN3155-005 R Figure 010
20-48-24 Page 13
Normal Contacts - Sleeve Shrinking Characteristics E0445, E0446, EN3155-004 and EN3155-005 R Figure 011
20-48-24 Page 1420-48-24 Page 15
R E. Crimping Procedure
R (Ref. Fig. 012)
R - Engage the stripped wire in the contact.
R - Make sure that you can see the wire through the contact hole.
R - Use the applicable tool.
R - Install the contact in the positioner.
R Fully close the tool handles until the safety ratchet releases.
R - Remove the crimped contact.
R - If sealing is necessary:
R - Heat shrink the sleeve if installed before stripping.
R - If it is necessary to use more than one sleeve, let the first sleeve become
R fully cool before you shrink the other sleeves.
Normal Contacts - Crimping Tools E0445, E0446, EN3155-004 and EN3155-005 R Figure 012
20-48-24 Page 1620-48-24 Page 17
R ________________________________________________________________________4. Connection Procedure for Contacts EN3155-003, EN3155-008, EN3155-014 and EN3155-015
R R A. Contact P/N and Characteristics (Ref. Fig. 013) ---------------------------------------------------------------------
| | USE WITH | | CONTACTS |------------------------------------------------| | | PLUG | RECEPTACLE | |------------------|-------------------------|----------------------| | EN3155-003 | | | | EN3155-008 | EN3545 - E0684 | EN3545 | | EN3155-014 | | | ---------------------------------------------------------------------
| EN3155-015 | EN3545 - E0684 | EN3545 - E0425 | ---------------------------------------------------------------------
R R B. Contact Insertion / Extraction Tools (Ref. Fig. 014)
R C. Wire Stripping (Ref. Fig. 015, 016)
(1) Normal wire
(a) If sealing is necessary, install the heat-shrinkable sleeve on the wire before stripping. Shrinking is done after crimping. Use applicable tool. Strip to the length "E".
(2) Special wires E0437 DL22 and DL20 NSA935132DJ20
R R (a) Remove the fiberglass braid then the PTFE envelope along a length of 50 mm (1.9685 in.).
R (b) Strip the core cable along a length of 35 mm (1.3779 in.).
(c) Install the heat shrinkable sleeve on the outer sheath along 10 mm (0.3937 in.) and shrink.
(d) Strip the core cable in the heat shrinkable sleeve to the normal length "E".
R Normal Contacts - P/N Characteristics EN3155-003, EN3155-008, EN3155-014 and EN3155-015 R Figure 013
20-48-24 Page 18
R Normal Contacts - Insertion/Extraction Tools EN3155-003, EN3155-008, EN3155-014 and EN3155-015 R Figure 014
20-48-24 Page 19
Normal Contacts - Special Wire Stripping and Sleeve Shrinking EN3155-003, EN3155-008, EN3155-014 and EN3155-015 R Figure 015
20-48-24 Page 20
R Normal Contacts - Wire Stripping Tools R EN3155-003, EN3155-008, EN3155-014 and EN3155-015 R Figure 016
20-48-24 Page 21
D. Crimping Procedure and Tools R (Ref. Fig. 017, 018)
(1)
Engage the stripped wire in the pin/socket.
(2)
Make sure that you can see the wire conductor through the inspection hole.
(3)
Install the pin/socket contact in the positioner.
(4)
Fully close the tool handles until the safety ratchet releases.
(5)
Remove the crimped contact.
(6)
If sealing is necessary:
-Heat shrink the sleeve.
20-48-24 Page 22
R Normal Contacts - Crimping Tools EN3155-003, EN3155-008, EN3155-014 and EN3155-015 R Figure 017
20-48-24 Page 23
R Normal Contacts - Crimping Tools R EN3155-003 and 3155-008 R Figure 018
20-48-24 Page 2420-48-24 Page 25
R ________________________________________________________5. Connection Procedure for Contacts EN3155-016 and ABS1493
R R R A. Contact P/N and Characteristics (Ref. Fig. 019) These contacts are used to connect copper cables.
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址：A320 ESPM Electrical Standard Practices Manual 4(36)
