R Coaxial Contacts - Insertion/Extraction Tools B Type E0375 - CANNON Contact Figure 010
20-48-32 Page 17
R Coaxial Contacts - Wire Stripping B Type E0375 - CANNON Contact Figure 011
20-48-32 Page 18
R Coaxial Contacts - Crimping Tools B Type E0375 - CANNON Contact Figure 012
20-48-32 Page 19
(i)
Install the contact body (7) on the assembly.
(j)
Crimp the zone of the braided shield with the applicable tool.
C. C Type E0375
(1)
Contact P/N and characteristics ---------------------------------------------------------------------| | USE WITH | | CONTACTS |------------------------------------------------| | | PLUG | RECEPTACLE | |------------------|-------------------------|----------------------| | C type | | | | E0375 | E0086 | -----| ---------------------------------------------------------------------
(2)
Contact insertion/extraction tools
Not applicable
(3)
Wire stripping procedure
(Ref. Fig. 013)
(a)
Slide the cup body (1) and ferrule (2) on the cable.
(b)
Strip the cable to the lengths A, B and C.
(4)
Crimping procedure and tools
(Ref. Fig. 014)
(a)
Slide the contact (3) on the center conductor.
(b)
Solder the conductor with the contact (3).
(c)
Put the ferrule (2) against the contact (3).
(d)
Crimp the ferrule with the braided shield with an applicable tool.
(e)
Put the cup body (1) against the crimped ferrule (2) assy.
(f)
Tighten the nut (4).
D. D Type E0375
(1) Contact P/N and characteristics
20-48-32 Page 20
Apr 01/05
R
R Coaxial Contacts - Layout and Wire Stripping C Type E0375 Figure 013
20-48-32 Page 21
R Coaxial Contacts - Crimping Tools C Type E0375 Figure 014
20-48-32 Page 22
---------------------------------------------------------------------| | USE WITH | | CONTACTS |------------------------------------------------| | | PLUG | RECEPTACLE | |------------------|-------------------------|----------------------| | D type | | | | E0375 | E0086 | -----| ---------------------------------------------------------------------
(2)
Contact insertion/extraction tools (Ref. Fig. 015)
(3)
Wire stripping procedure (Ref. Fig. 016)
(a) Strip the wire to the length A with an applicable tool.
(4)
Crimping procedure and tools (Ref. Fig. 017)
(a)
Slide the ferrule (1) on the braided shield (2). Stop the ferrule (1) against the insulation (3) of the cable.
(b)
Turn the braided shield over the ferrule.
(c)
Make sure that the length B is correct.
(Ref. Fig. 016)
(d)
Strip the wire to the length D.
(Ref. Fig. 016)
(e)
Make sure that the length C is correct.
(Ref. Fig. 016)
(f)
Slide the rear insulation (3) against the braided shield (2).
(g)
On the wire conductor (6), install the inner contact (4) against the rear insulation (3). Make sure that you can see the wire conductor through the inspection hole.
(h)
Crimp the contact (4) with conductor (6), with an applicable tool.
20-48-32 Page 23
Apr 01/05
R
R Coaxial Contacts - Insertion/Extraction Tools D Type E0375 - RADIALL Contact Figure 015
20-48-32 Page 24
R Coaxial Contacts - Wire Stripping D Type E0375 - RADIALL Contact Figure 016
20-48-32 Page 25
R Coaxial Contacts - Crimping Tools D Type E0375 - RADIALL Contact Figure 017
20-48-32 Page 26
INTENTIONALLY BLANK
R
20-48-32 Page 27
Apr 01/05
INTENTIONALLY BLANK
R
20-48-32 Page 28
Apr 01/05
(i)
Slide the contact body (5) on the braided shield zone.
(j)
Crimp the zone E of the contact body.
20-48-32 Page 29
Apr 01/02
R
R _____________________________________________________6. Connection Procedure for CANNON Type Coaxial Contacts
R R R A. Contact P/N and Characteristics (Ref. Fig. 018) ---------------------------------------------------------------------| | USE WITH | | CONTACTS |------------------------------------------------| | | PLUG | RECEPTACLE | |------------------|-------------------------|----------------------| | CANNON | | | | 249-1741-000 | E0083 | E0083 | | CANNON | NSA938310 | NSA938310 | | 249-9008-000 | | | ---------------------------------------------------------------------
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址：A320 ESPM Electrical Standard Practices Manual 4(48)
