-
For DEUTSCH contact only: . Insert the dielectric (12) over the contacts making sure that the positioning slot (11) is located between the red and yellow conductors
-Insert the contact body (13) making sure that the positioning slot(11) is aligned with the pin (14) of the body (13) until the ferrule is covered.
-Make sure that the length of ferrule not covered by the contact body before crimping is 1.4 mm (0.0551 in.) max.
-Crimp with applicable tool at the rear of the contact body (13).
-Cut the protruding braid strands.
E. Sealing sleeve installation (Ref. Fig. 003)
(1)
Insert the crimped contact in the connector insert with the
applicable tool.
(2)
Slide the sealing sleeve (1) inside the connector insert cavity until it reaches the bottom. The sealing sleeve abutment must be in contact with the rear of the connector grommet.
20-48-36 Page 7
__________________________________________________________
MISCELLANEOUS TRIAXAL CONTACTS - DESCRIPTION AND OPERATION
_______1. General
The triaxial contacts installed on aircraft have the codes that follow:
- EN3155-012
- EN3155-013
- EN3155-042
- EN3155-043
__________________________________________________________________________2. Typical connection procedure for triaxial contacts EN3155-012, EN3155-013,
EN3155-042 and 3155-043
A. Contact P/N and characteristics
R -------------------------------------------------------------
R | | USE WITH |
R | CONTACTS |--------------------------------------------|
R | | PLUG | RECEPTACLE |
R |--------------|---------------------|----------------------|
R | EN3155-012 | - | EN3645 |
R |--------------|---------------------|----------------------|
R | EN3155-013 | EN3645 | - |
R |--------------|---------------------|----------------------|
R | EN3155-042 | EN3682 | EN3682 |
R | EN3155-043 | | |
R -------------------------------------------------------------
R
R EN3155-013 F 08 A B
R EN3155-042 M 08 B
R EN3155-043 F 08 B
R | | | | |
| | | | ----- Code for delivery conditions | A : Without sleeve
| | | | | B : With sleeve
| | | |
R | | | -------- Permitted cable code (Only for EN3155-012
R | | | and EN3155-013 )
| | |
| | ------------ Contact size code
| |
| ---------------- Type of contact | M : Male
| | F : Female
|
------------------------- Standard P/N
20-48-39 Page 120-48-39 Page 2
R B. Characteristics
R R (1) Temperature
R R (a) EN3155-012 and EN3155-013 Minimum operating temperature is -65 deg.C (-85.00 deg.F) Maximum operating temperature is 150 deg.C (302.00 deg.F)
R (b) EN3155-042 and EN3155-043 Minimum operating temperature is -65 deg.C (-85.00 deg.F) Maximum operating temperature is 125 deg.C (257.00 deg.F)
R R R R R R R R R R (2) Cable code (Only for EN3155-012 and EN3155-013) -------------------------------------------------| CABLE CODE | CABLE P/N | |-----------------|-----------------------------| | A | EN3375-003 | |-----------------|-----------------------------| | B | EN3375-004 | |-----------------|-----------------------------| | C | EN3375-005 | -------------------------------------------------
C. Contact insertion and extraction tools (Ref. Fig. 001)
D. Wire stripping (Ref. Fig. 002)
E. Soldering procedure (Ref. Fig. 003)
(1) Engage the conductors in the contacts: - wite conductor: center contact. - color conductor: intermediate contact. - engage the cable until it touches the contact (center conductor). - do a check of the position of the color conductor and the position of the sleeve as shown.
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址：A320 ESPM Electrical Standard Practices Manual 4(54)
