1EFF : 051-099, 1 56-12-11Page 469 1 1 May 01/05 1 1 1CES 1
R Subtask 56-12-11-420-059
R B. Installation of the Sliding Window Panel
R (Ref. Fig. 415/TASK 56-12-11-991-029)
R CAUTION : BE CAREFUL DURING THE REMOVAL/INSTALLATION OF EACH SLIDING_______
R WINDOW PANEL TO PREVENT INJURY TO PERSONS AND /OR DAMAGE.
R MAKE SURE THAT THERE ARE SUFFICIENT PERSONS DURING THE
R OPERATION. EACH WINDOW PANEL WEIGHS APPROXIMATELY 20Kg
R (44.11b).
R (1) Use 2 suction cups to move and hold the sliding window panel (30) in
R position during installation in its frame.
R (2) Put the sliding window panel (30) and the retainer (31) in position
R in its housing.
R (3) Move the frame of the sliding window to the closed position.
R (4) Install four screws (32) at the four corners of the frame .
R (5) Move the frame of the sliding window to the open position.
R (6) Install all the screws (32) and washers (33) and tighten with your
R hand.
R (7) Install 4 non metallic shims between the sliding window panel (30)
R and the retainer (31) to get a clearance A of 1.4 +1 -1 mm (0.0551
R +0.0393 -0.0393 in.).
R (8) Install the washers (33) and the screws (32) at the four corners of
R the frame.
R (9) Initially TORQUE the screws (32) to 0.2 m.daN (17.69 lbf.in). For the
R screw (32) behind the axis of the control handle, use the WRENCH,
R REMOVAL - SLIDING WINDOW (98D56103002001).
R (10) TORQUE the screws (32) to between 0.35 and 0.45 m.daN (30.97 and
R 39.82 lbf.in).
R NOTE : TORQUE the screws (32) in a staggered pattern.____
R (11) Remove the non metallic shims.
R (12) Apply SEALANTS (Material No. 09-016) in the peripheral gap.
1EFF : 051-099, 1 56-12-11Page 470 1 1 May 01/05 1 1 1CES 1 1EFF : 051-099, 1 56-12-11Page 471 1 1 May 01/05 1 1 1CES 1
R (13) Clean the remaining sealing compound between the window panel (30)
R and the retainer (31) with a MISCELLANEOUS (Material No. 19-003)
R soaked with CLEANING AGENTS (Material No. 11-003).
R **ON A/C 051-051,
R Subtask 56-12-11-220-059
R C. Check of the Clearance
R (Ref. Fig. 416/TASK 56-12-11-991-047)
R (1) Make sure that the sliding window is open.
R (2) Do a check of the out-of-flush clearance C between the retainer (34)
R and the sliding window panel (30).
R NOTE : The clearance C (edge-clearance) between the window frame and____
R window panel, shows a defect in the flat surfaces of the panel
R and the frame.
R The edge-clearance location is at the window panel/frame edge.
R (a) Make sure that the out-of-flush clearance C between the retainer
R (34) and the glass sliding window (30) is 0.6 +0.8 -0.7 mm
R (0.0236 +0.0314 -0.0275 in.).
R (3) Close the sliding window. Make sure that the window moves easily.
R (4) From points 1 to 11 make sure that the out-of-flush B is 0 +0.6 -2 mm
R (0.0000 +0.0236 -0.0787 in.) on the periphery of the window panel.
R (5) If the out-of-flush B is not correct, adjust as follows:
R (a) Remove the circlips (42), (45), (46) and (51).
R (b) Loosen the nuts (41), (44), (47) and (50).
R (c) Turn the eccentrics (40), (43), (48) and (49) to get the correct
R out-of-flush B.
R (d) TORQUE the nuts (41), (44), (47) and (50) to between 0.6 and 0.7
R m.daN (53.09 and 61.94 lbf.in).
R (e) Safety the nuts (41), (44), (47) and (50) with BONDING AND
R ADHESIVE COMPOUNDS (Material No. 08-002A).
R (f) Install the circlips (42), (45), (46) and (51).
R Sliding Windows - Clearances
R Figure 416/TASK 56-12-11-991-047- 12 (SHEET 1)
1EFF : 051-052, 1 56-12-11Page 472 1 1 May 01/05 1 1 1CES 1
R Sliding Windows - Clearances
R Figure 416/TASK 56-12-11-991-047- 22 (SHEET 2)
1EFF : 051-052, 1 56-12-11Page 473 1 1 May 01/05 1 1 1CES 1 1EFF : 052-052, 1 56-12-11Page 474 1 1 May 01/05 1 1 1CES 1 1EFF : 052-099, 1 56-12-11Page 475 1 1 May 01/05 1 1 1CES 1 中国航空网 www.aero.cn 航空翻译 www.aviation.cn 本文链接地址：A320飞机维护手册 AMM WINDOWS 风挡 窗户(65)
