R Subtask 56-11-11-820-052
R D. Adjustment of the Windshield
R (Ref. Fig. 408/TASK 56-11-11-991-023)
R CAUTION : DO NOT USE A SUCTION CUP TO HOLD THE INNER SURFACE OF THE_______
R WINDSHIELD PANEL IF THE PANEL HAS A SOFT (SELF HEALING) LINER
R (SUPPLIER SPS).THE SUCTION CUP WILL CAUSE DAMAGE TO THE SOFT
R LINER.
R -DO NOT TRY TO REMOVE THE SOFT LINER.
R THE SOFT LINER IS A PART OF THE WINDSHIELD PANEL.
R CAUTION : REMOVE THE WINDSHIELD PANELS FROM THEIR CONTAINER ONLY WHERE_______
R AND WHEN YOU INSTALL THEM.
R KEEP THE PROTECTIVE FILM ON THE INTERNAL AND EXTERNAL SURFACES
R OF THE WINDSHIELD :
R - WHEN YOU INSTALL THE PANELS
R - WHEN YOU USE THE CENTERING TOOL.
R (1) Put the R/I FRONT WINDOW TOOL (98F56103000000) in position in the
R windshield housing.
R (2) Adjust the windshield panel (14) to get a clearance J1 of 1 -1 +0.5
R mm (0.0393 -0.0393 +0.0196 in.) related to the lateral post.
R (3) Remove the R/I FRONT WINDOW TOOL (98F56103000000).
R Subtask 56-11-11-420-059
R E. Installation of the Retainers
R (Ref. Fig. 402/TASK 56-11-11-991-002)
R (1) Install the upper retainer (31) and the front retainer (18).
R (2) Apply SPECIAL MATERIALS (Material No. 05-002) below the head of the
R screws (13), (23), (24), (27) and (32).
R (3) Install the washers (25), (29) and (30), the screws (13), (23), (24),
R (27) and (32), the washers (10) and the nuts (11) and lightly tighten
R them.
R NOTE : The screws (24) and (32) are different lengths.____
R Make sure that you install them at their correct position.
1EFF : ALL 1 56-11-11Page 443 1 1 Aug 01/05 1 1 1CES 1 1EFF : ALL 1 56-11-11Page 444 1 1 Aug 01/05 1 1 1CES 1 1EFF : 001-049, 051-099, 101-108, 151-199, 1 56-11-11Page 445 1201-299, 301-399, 1Aug 01/05 1 1 1CES 1
R (4) Install the icing indicator (26), the washer (17) and the nut (16).
R NOTE : Do an electrical bonding of the icing indicator (26) when you____
R install it.
R (5) Tighten the nuts (11) and (16) and the screws (13), (23), (24), (27)
R and (32) with your hand.
R (6) In a staggered pattern, initially TORQUE the nuts (11) and (16) and
R the screws (13), (23), (24), (27) and (32) to between 0.4 and 0.5
R m.daN (2.94 and 3.68 lbf.ft).
R (7) In a staggered pattern, finally TORQUE the nuts (11) and (16) and the
R screws (13), (23), (24), (27) and (32) to between 1.6 and 1.8 m.daN
R (11.79 and 13.27 lbf.ft).
R (8) Remove the shims between the lower retainer (18) and the windshield
R panel (6) and the aircraft structure.
R (9) Remove the blanking caps from the electrical connectors.
R (10) Connect the sensor (15).
R (11) Connect the electrical connector (43).
R (12) Attach the electrical cable (41) against the draining pipe (44) with
R the cable ties (42).
R **ON A/C 001-049, 051-099, 101-108, 151-199, 201-299, 301-399,
R Subtask 56-11-11-220-053
R F. Check of the Clearances
R (Ref. Fig. 407/TASK 56-11-11-991-003)
R (1) Do a check of the clearances on the points given in the figure and
R make sure that:
R (a) The peripheral clearance J1 between the retainers and the window
R panel and between the window panel and the frame is:
R 1 0 mm (0.0000 in.) to 2.0 mm (0.0787 in.) on 20 % of the_
R measured points
R 2 0 mm (0.0000 in.) to 1.5 mm (0.0590 in.) on the other measured_
R points.
R (b) The out-of-flush dimension J2 between the window panel and the
R retainers is:
R 1_ 0.7 -0.6 +0.6 mm (0.0275 -0.0236 +0.0236 in.) for all the
R windshields (not applicable to SPS windshields P/N STA320-1-7
R and STA320-2-7 and to PPG windshields P/N NP165311-5 and P/N
R 165311-6).
R 2_ 0.7 -0.1 +1.4 mm (0.0275 -0.0039 +0.0551 in.) for SPS
R windshields P/N STA320-1-7 and STA320-2-7 and PPG windshields
R P/N NP165311-5 and P/N 165311-6.
R 3_ 1.4 -0.3 +1.8 mm (0.0551 -0.0118 +0.0708 in.) for PILKINGTON
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址：A320飞机维护手册 AMM WINDOWS 风挡 窗户(27)
