1EFF : ALL 1 56-11-11Page 401 1 1 Aug 01/05 1 1 1CES 1 B. Referenced Information
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
30-45-44-000-001 Removal of the Spray Nozzle
30-45-52-000-002 Removal of the Wiper Arm (306DM, 307DM)
56-11-11-991-001 Fig. 401
56-11-11-991-002 Fig. 402
56-11-11-991-022 Fig. 403
56-11-11-991-014 Fig. 404
3. Job Set-up
__________
Subtask 56-11-11-010-050
A. Get Access
R (1) Put an access platform in position at zone 210 in front of the R windshield.
(2) Remove the wiper arm (Ref. TASK 30-45-52-000-002).
Subtask 56-11-11-865-050
B. Open, safety and tag this(these) circuit breaker(s):
-------------------------------------------------------------------------------PANEL DESIGNATION IDENT. LOCATION -------------------------------------------------------------------------------49VU LIGHTING/ICE AND STBY/COMP/LIGHT 1LF H04 121VU COM NAV/RADAR/1 5SQ1 K13
**ON A/C 051-099,
121VU COM NAV/RADAR/2 5SQ2 K14
**ON A/C ALL
122VU ANTI ICE/WINDOWS/R 4DG2 W14 122VU ANTI ICE/WHC/2 5DG2 W13 122VU ANTI ICE/WINDOWS/L 4DG1 X14 122VU ANTI ICE/WHC/1 5DG1 X13 123VU ANTI ICE/L/WHSLD 1DG1 AF10
1EFF : ALL 1 56-11-11Page 402 1 1 Aug 01/05 1 1 1CES 1 -------------------------------------------------------------------------------PANEL DESIGNATION IDENT. LOCATION -------------------------------------------------------------------------------
123VU ANTI ICE/R/WHSLD 1DG2 AF03
4. Procedure
_________ Subtask 56-11-11-020-050
A. Removal of the Components
(Ref. Fig. 401/TASK 56-11-11-991-001)
(1)
Release the four stud assy (3).
(2)
Loosen the fastener (5) and remove the lining panel 211LW (4) which prevents damage to the sensors.
(3)
Remove the screws (2) and the washers (6).
(4) Remove the vertical lining panel 211MW (1). Subtask 56-11-11-020-052-A
B. Removal of the Windshield Retainers
(Ref. Fig. 402/TASK 56-11-11-991-002)
NOTE : If you find fasteners that you cannot remove easily, do the
____
procedure with the fastener removal tool in para (2).
(1) Removal of the retainers:
(a)
Disconnect the sensor (15).
(b)
Remove and discard the cable ties (42) that attach the electrical cable (41) against the draining pipe (44).
(c)
Disconnect the electrical connector (43).
(d)
Put blanking caps on the disconnected electrical connectors.
(e)
Remove the sealant from the screw heads.
(f)
Remove the screws (20), (21) and (22).
(g)
Remove the protection plate (19).
(h)
Remove the spray nozzles (Ref. TASK 30-45-44-000-001).
1EFF : ALL 1 56-11-11Page 403 1 1 Aug 01/05R 1 1 1CES 1
Windshield - Component Location Figure 401/TASK 56-11-11-991-001
1EFF : 1 1R 1CES ALL 1 11 1 56-11-11 Page 404 Aug 01/05
INTENTIONALLY BLANK
R 1 1
56-11-11Page 405
1 1 Aug 01/05 1 1 1CES 1
R Windshield - Removal/Installation Figure 402/TASK 56-11-11-991-002- 12 (SHEET 1)
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址:A320飞机维护手册 AMM WINDOWS 风挡 窗户(16)