R 1EFF : 001-049, 051-099, 101-149, 221-221, 1 52-33-11Page 520 1224-224, 228-228, 1May 01/05 1 1 1CES 1
Clearance Check of the Forward and Aft Barrel Locks
Figure 504/TASK 52-33-11-991-004
R 1EFF : 001-003, 051-054, 1 52-33-11Page 521 1 1 May 01/05 1 1 1CES 1
Clearance Check of the Forward and Aft Barrel Locks Figure 504A/TASK 52-33-11-991-004-A
R 1EFF : 004-049, 055-099, 101-149, 221-221, 1 52-33-11Page 522 1224-224, 228-228, 1May 01/05 1 1 1CES 1
R **ON A/C 001-003, 051-054,
(Ref. Fig. 505/TASK 52-33-11-991-005)
R **ON A/C 004-049, 055-099, 101-149, 221-221, 224-224, 228-228,
(Ref. Fig. 505A/TASK 52-33-11-991-005-A)
R **ON A/C 001-003, 051-052,
(Ref. Fig. 506/TASK 52-33-11-991-007)
R **ON A/C 004-049, 055-099, 101-149, 221-221, 224-224, 228-228,
(Ref. Fig. 506A/TASK 52-33-11-991-007-B)
R **ON A/C 053-054,
R (Ref. Fig. 506B/TASK 52-33-11-991-007-A)
R **ON A/C 001-049, 051-099, 101-149, 221-221, 224-224, 228-228,
Subtask 52-33-11-820-054
A. Adjustment of the Locking Mechanism
(1) Make sure that the notches of the serrated plates and the forward/aft latch spigots are aligned (Ref. TASK 52-33-32-400-001).
(2) Put the GAGE - MEASURING, BULK CARGO DOOR LOCKING MECHANISM (98A52307622000) in the inspection hole of the forward/aft barrel locks to examine the locking mechanism.
NOTE : If you can see the red marking ring of the GAGE - MEASURING,____ BULK CARGO DOOR LOCKING MECHANISM, the adjustment of the locking mechanism is correct.
(3) If you can not see the red marking ring of the measuring gage, adjust the locking mechanism as follows:
(a) Cut and remove the lockwire from the jam nuts (34).
R 1EFF : 001-049, 051-099, 101-149, 221-221, 1 52-33-11Page 523 1224-224, 228-228, 1May 01/05 1 1 1CES 1
Adjustment of the Forward and Aft Barrel Locks
Figure 505/TASK 52-33-11-991-005
R 1EFF : 001-003, 051-054, 1 52-33-11Page 524 1 1 May 01/05 1 1 1CES 1
Adjustment of the Forward and Aft Barrel Locks
Figure 505A/TASK 52-33-11-991-005-A
R 1EFF : 004-049, 055-099, 101-149, 221-221, 1 52-33-11Page 525 1224-224, 228-228, 1May 01/05 1 1 1CES 1
Adjustment of the Push Rod and Door Handle
Figure 506/TASK 52-33-11-991-007
R 1EFF : 001-003, 051-052, 1 52-33-11Page 526 1 1 May 01/05 1 1 1CES 1
Adjustment of the Push Rod
Figure 506A/TASK 52-33-11-991-007-B
R 1EFF : 004-049, 055-099, 101-149, 221-221, 1 52-33-11Page 527 1224-224, 228-228, 1May 01/05 1 1 1CES 1
R Adjustment of the Push Rod
R Figure 506B/TASK 52-33-11-991-007-A
R 1EFF : 053-054, 1 52-33-11 Page 528
1 1 May 01/05
1 1
1CES 1
(b)
Loosen the jam nuts (34) and release the locking rings (33).
(c)
Turn the push rod (32) clockwise or counterclockwise until the adjustment is correct.
NOTE : Make sure that the threads of the eye ends cover the
____
inspection hole of the rod body.
(d)
Set the locking rings (33) in the correct position and tighten the jam nuts (34).
(e)
Safety the jam nuts (34) with lockwire, corrosion-resistance steel, dia 0.8 mm on the locking ring (33).
(f)
Remove the measuring gage from the inspection hole of the forward and aft barrel locks (20).
(4)
Make sure that the external door handle is in the center of the recess at the outer skin.
(5)
If not, adjust the position of the external door handle as follows:
(a)
Cut and remove the lockwire (44) from the jam nut (42).
(b)
Loosen the jam nut (42) and turn the adjustment screw (43) until the external door handle is in the center position.
(c)
Tighten the jam nut (42) and safety it with the MISCELLANEOUS (Material No. 19-010).
(6)
Adjust the overturn stop of the locking mechanism as follows:
(a)
Move the door handle to the OPEN position to release the Bulk door.
(b)
Make sure that the claws of the barrel locks (20) do not engage with the related latch spigots on the fuselage frame.
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址：A320飞机维护手册 AMM DOORS 舱门6(37)
