(a)
Apply a thin layer of the SPECIAL MATERIALS (Material No. 05-002) to the bolt (2), the washers (19) and the nut (18).
(b)
Put the eye-end (1) in its installation position and attach it with the bolt (2), the washers (19) and the nut (18).
(c)
Tighten the nut (18) and safety it with the cotter pin (17).
(d)
Apply SPECIAL MATERIALS (Material No. 05-005) to the head of the bolt (2) and the nut (18)
(6)
Remove the pip-pin (6) from the rigging hole of fuselage fitting and put it in the stowage hole.
(7)
Install the air intake diffuser and the elbow (Ref. TASK 49-16-45-400-002).
**ON A/C ALL
Subtask 52-41-22-820-050
E. Adjustment Procedure
(1)
Close the APU access doors 316AR and 315AL (Ref. TASK 52-41-00-410-001).
(2)
Make sure that the locking hooks of the quick-release fasteners are correctly engaged in the clevises (14).
(3)
Measure the force necessary to move the lever (16) of the latch (15) with the spring gage (capacty min. 20.0 daN (44.96 lbf).
NOTE : The force must be between 8.0 daN (17.9847 lbf) and 18.0 daN
____ (40.4656 lbf) and is measured 90 mm (3.5433 in.) from the rear end of the latch (15).
(4) If the force is out of tolerance, adjust the clevises (14) as follows:
(a) Open the APU access doors 315AL, 316AR (Ref. TASK 52-41-00-010-001).
1EFF : ALL 1 52-41-22Page 418 1 1 May 01/05 1 1 1CES 1
(b) Loosen the nuts (13) and turn the clevises (14) in or out until the the force is correct.
NOTE : When you adjust the force, try at the upper tolerance
____
limit.
(c) Tighten the nuts (13).
(d) Adjust the clevises (14) in the sequence front-rear-center. Subtask 52-41-22-910-051
F. Preparation after Installation
(1)
Seal the head of the bolt (33) and the nut (29) with SEALANTS (Material No. 09-013).
(2)
Apply to the heads of the bolts (21) ,(33) ,(41) and to the nuts (25),(29),(37) SPECIAL MATERIALS (Material No. 05-005).
5. Close-up
________ Subtask 52-41-22-410-051
A. Close Access
(1)
Make sure that the work area is clean and clear of tool(s) and other items.
(2)
Close the APU access doors 316AR, 315AL (Ref. TASK 52-41-00-410-001).
(3) Remove the access platform(s). Subtask 52-41-22-865-052
B. Remove the safety clip(s) and the tag(s) and close this(these) circuit breaker(s): 1KD, 2KD.
1EFF : ALL 1 52-41-22Page 419 1 1 May 01/05 1 1 1CES 1 DOOR - MAINTENANCE - REMOVAL/INSTALLATION
_________________________________________
TASK 52-41-23-000-001
Removal of the Maintenance Door 314AR
WARNING : DO NOT TOUCH THE APU UNTIL IT IS SUFFICIENTLY COOL TO PREVENT BURNS
_______
WHEN YOU DO THE MAINTENANCE TASK(S).
1.
Reason for the Job
__________________
Self Explanatory
2.
Job Set-up Information
______________________
A. Fixtures, Tools, Test and Support Equipment
-------------------------------------------------------------------------------
REFERENCE QTY DESIGNATION
-------------------------------------------------------------------------------
No specific warning notice
No specific access platform 3.7 m (12 ft. 2 in.)
B. Referenced Information
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
**ON A/C 001-049, 051-099, 101-105, 151-158, 201-210,
52-41-23-991-001 Fig. 401 R **ON A/C 106-149, 159-199, 211-299, 301-399, 401-499,
52-41-23-991-001-A Fig. 401A
1EFF : ALL 1 52-41-23Page 401 1 1 Aug 01/05 1 1 1CES 1 **ON A/C ALL
3. Job Set-up
__________
Subtask 52-41-23-860-050
A. Aircraft Maintenance Configuration
(1)
Put the warning notice in the flight compartment to tell persons not to start the APU.
(2)
Put the access platform in position below the maintenance door 314AR.
(3)
Release the quick-release fasteners and open the maintenance door 314AR (5).
4. Procedure
_________
**ON A/C 001-049, 051-099, 101-105, 151-158, 201-210,
(Ref. Fig. 401/TASK 52-41-23-991-001) R **ON A/C 106-149, 159-199, 211-299, 301-399, 401-499,
(Ref. Fig. 401A/TASK 52-41-23-991-001-A)
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址：A320飞机维护手册 AMM DOORS 舱门6(165)
