A320飞机维护手册 AMM DOORS 舱门6(158)

曝光台 注意防骗 网曝天猫店富美金盛家居专营店坑蒙拐骗欺诈消费者

 (1) Remove and discard the sealing profiles (1) and (8) from the frames FR 80 and FR 84.
 (2) Remove the old adhesive with the CLEANING AGENTS (Material No. 11-003):
 (3) Remove the old sealant at the bottom of FR 80 with a wooden or plastic scraper.
 (4) Remove the fasteners (10) and the rivets (11) which hold the sealing strips (2), (3), (4) and (5) at the two sides of the tail cone.
 (5) Remove the sealing strips (2), (3), (4) and (5) and discard the sealing profiles.
 (6) Remove the old adhesive with the CLEANING AGENTS (Material No. 11-003).
 (7) Clean the mating surfaces of the structure and the new sealing profiles with the CLEANING AGENTS (Material No. 11-003) and a clean lint-free cloth.
 (8) Put the sealing profiles (1) and (8) on the frames FR 80 and FR 84 and make a mark at the ends.

 

 (9) Cut the ends of the sealing profiles (1) and (8) to make a mitre.
 (10) Bond the sealing profiles (1) and (8) to the frames FR 80 and FR 84 with the BONDING AND ADHESIVE COMPOUNDS (Material No. 08-006).
 NOTE : Obey the adhesive manufacturer's instructions.
____
 (11)
 Put the sealing profiles (9) into position and make a mark at the ends.

 (12)
 Cut the ends of the sealing profiles (9) to make a mitre.

 (13)
 Bond the ends of the sealing profiles (9) to the ends of the sealing profiles (1) and (8) with BONDING AND ADHESIVE COMPOUNDS (Material No. 08-006).

 (14)
 Bond the sealing profiles (9) to the structure with the BONDING AND ADHESIVE COMPOUNDS (Material No. 08-006).

 (15)
 Apply the SEALANTS (Material No. 09-013) to the rivets (11) and the fasteners (10).

 (16)
 Install the sealing strips (2), (3), (4) and (5) to the structure with the rivets (11).

 (17)
 Install the fasteners (10), the washers (7) and the nuts (6).

 (18)
 Fill the bottom of the frame FR 80 up to the sealing profile top and 200 mm (7.8740 in.) to the two sides from the frame centre with SEALANTS (Material No. 09-016).

 (19)
 Apply a layer of the STRUCTURE PAINTS (Material No. 16-003) to the sealant.

 Subtask 52-41-21-390-050
 D. Replacement of the Sealant at the Corners
 (1)
 Remove the old sealant and clean the corner surface with CLEANING AGENTS (Material No. 11-003).

 (2)
 Fill up the joggles at the four corners of the door with SEALANTS (Material No. 09-016) and make the surface smooth.

 (3)
 Let the sealant cure.

 1EFF : ALL 1 52-41-21Page 411 1 1 Feb 01/98 1 1 1CES 1 Subtask 52-41-21-960-052

 E. Replacement of the Strut Bracket of the Access Door
 (1) If the bracket is damaged, replace it as follows:
 (a)
 Replace the pip-pin (32).

 (b)
 Remove the nut (19), the bolt (21) and the door strut (22).

 (c)
 Remove the screws (16), (17), the washers (15), (18) and the brackets (14), (20).

 (d)
 Apply the SPECIAL MATERIALS (Material No. 05-002) to the screws (16), (17), to the washers (15), (18) and to the bolt (21).

 (e)
 Apply the SEALANTS (Material No. 09-013) to the mating surfaces of the door strut bracket (20) and the bracket (14).

 (f)
 Install the replacement door strut bracket (20) and the bracket

 (14) with the screws (16), (17) and the washers (15), (18).

 (g)
 Install the door strut (22) with the bolt (21) and the nut (19).

 (h)
 Apply the SEALANTS (Material No. 09-016) to the screws (16), (17) to the washers (15), (18), to the bolt (21) and to the nut (19).

 (i) Lock the pip-pin (32). Subtask 52-41-21-560-050
 F. Preparation of a Replacement Component
 WARNING : USE SOLVENTS/CLEANING AGENTS, SEALANTS AND OTHER SPECIAL

_______ MATERIALS ONLY WITH A GOOD SUPPLY OF AIR. OBEY THE MANUFACTURERS INSTRUCTIONS. PUT ON PROTECTIVE CLOTHING. DO NOT GET THEM IN YOUR MOUTH. DO NOT SMOKE. DO NOT BREATHE THE GAS. THESE MATERIALS ARE POISONOUS, FLAMMABLE AND SKIN IRRITANT. GET MEDICAL HELP IF YOUR SKIN OR EYES BECOME IRRITATED.
 1EFF : ALL 1 52-41-21Page 412 1 1 Feb 01/98 1 1 1CES 1

 (1) If you replace the APU access door, do the subsequent:
 (a)
 Release the pip-pin (32).

 (b)
 Remove the nut (19) , the bolt (21) and the access door strut (22).

 (c)
 Apply the SPECIAL MATERIALS (Material No. 05-002) to the bolt (21).

 (d)
 Install the access door strut (5) with the bolt (6) and the nut

 (4) on the replacement APU access door (1).
　
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址：A320飞机维护手册 AMM DOORS 舱门6(158)