-
the IGV position,
-
the load control valve,
-
the surge control valve position.
The ECB also controls the subsequent systems:
-
the starter motor,
-
the igniters,
-
the fuel control shutoff valve,
-
the air intake flap.
The ECB communicates with the aircraft systems through the ARINC 429
busses.
The subsequent LRUs are controlled by separate torque motor currents:
-
the fuel control assembly,
-
the IGV actuator,
-
the surge control valve.
R **ON A/C 401-499,
R A. Electronic Control Box 59KD
R (1) The ECB is installed adjacent to the BULK cargo compartment on the
R right side, between FR54 and FR55. It is held in an ARINC 600-6
R mounting rack.
R The ECB provides full authority digital APU control from the start
R initialization, during the acceleration, at the governor speed to the
R shutdown. The ECB monitors the APU speed, the APU temperatures, the
R load compressor air flow, and other critical parameters based on
R signal inputs from the accessory sensors and the control switches.
R These data are used for the calculation and to continuously control:
R - the fuel flow,
R - the IGV position,
R - the load control valve,
R - the surge control valve position.
R The ECB also controls the subsequent systems:
R - the starter motor,
R - the igniters,
R - the fuel control shutoff valve,
R - the air intake flap.
R The ECB communicates with the aircraft systems through the ARINC 429
R busses.
R The subsequent LRUs are controlled by separate torque motor currents:
R - the fuel control assembly,
R - the IGV actuator,
R - the surge control valve.
R **ON A/C 001-003, 051-099, 401-499,
4. Power Supply____________
(Ref. Fig. 002)
The battery bus 301PP supplies 28VDC to the ECB 59KD through the circuit
breaker ECB SPLY 1KD and the relay APU MAIN 4KD. The 28VDC supply for the
APU MAIN relay is through the circuit breaker APU CTL 2KD. The ECB
continuously monitors its internal voltages and starts an APU shutdown if a
voltage failure occurs (that would result in an unsafe operation of the
APU).
5. Interface_________
CES
ECB Supply - Electrical Schematic
Figure 002
CES
**ON A/C 001-003, 051-062,
A. Aircraft (A/C) Input Signals to the ECB 59KD
------------------------------------------------------------------------
INPUT SIGNAL SIGNAL
------------------------------------------------------------------------
Master Switch/Stop Ground/Open
Start 28 V DC
Environmental Control System (ECS) ARINC 429 BUS
air demand
Main Engine Start (MES) 28 V DC
Emergency Shutdown Ground
Bleed-air Valve Operation Ground
Air/ground Signal Ground for ground
condition
A/C Parameter and Centralized Fault ARINC 429 BUS
Display System (CFDS)
Start Contactor Monitor Signal Open/28 V/ground
TSO/JAR Configuration Open/Ground
for TSO Configuration
Air Intake Actuator BITE Signals 2 x 28 V DC
Start Valve Command 28 V DC
Low Fuel Pressure Valve enable GND for BITE enable
APU Oil Heater BITE enable GND for BITE enable
(1) A/C Sensors connected to the ECB 59KD:
- low-level pressure switch 5030 QM
- generator oil-temperature sensor,
- air-intake position switches.
(2) ECB 59KD Output Signals to the A/C
--------------------------------------------------------------------LOAD OUTPUT SIGNAL SIGNAL STEADY CONDITION STATE --------------------------------------------------------------------
APU AVAILABLE 28 V DC 150 mA
Start Contactor 28 V DC 1 A
Back-Up Start Contactor 28 V DC 1 A
APU Fault 28 V DC 50 mA
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址：A320飞机维护手册 AMM 机载辅助动力 AIRBORNE AUXILIARY POWER5(67)
