Material No. 11-004 USA MIL-T-81533
1.1.1TRICHLOROETHANE (METHYL CHLOROFORM)
(Ref. 20-31-00)
Material No. 15-005 AIB TN 10138 TYPE I GRADE 2 CORROSION PREVENTIVE TEMPORARY PROTECTIVE COMPOUND (Ref. 20-31-00)
Material No. 15-006 AIB TN 10138 TYPE I GRADE 3 CORROSION PREVENTIVE TEMPORARY PROTECTIVE COMPOUND (Ref. 20-31-00)
Material No. 15-007 AIB TN 10138 TYPE II GRADE 1 CORROSION PREVENTIVE TEMPORARY PROTECTIVE COMPOUND (Ref. 20-31-00)
Material No. 15-008 AIB TN 10138 TYPE II GRADE 2 CORROSION PREVENTIVE TEMPORARY PROTECTIVE COMPOUND (Ref. 20-31-00)
Material No. 19-003 USA AMS 3819
LINT-FREE COTTON CLOTH (Ref. 20-31-00)
R C. Referenced Information
R -------------------------------------------------------------------------------R REFERENCE DESIGNATION R -------------------------------------------------------------------------------
R 52-10-00-010-001 R 52-10-00-410-001 R 52-11-31-000-005 R 52-11-31-400-005 R SRM 511100,P.Block 001 R SRM 512200,P.Block 001 R 53-11-00-991-094
R 3. Job Set-up
__________
R Subtask 53-11-00-010-104
R A. Get Access Opening of the Passenger/Crew Door Closing of the Passenger/Crew Door Removal of the Girt-Bar Fitting Blanking-Plates Installation of the Girt-Bar Fitting Blanking-Plates (for corrective action) (for corrective action) Fig. 659
R (1) Put an access platform in position at zone 831 (841).
R (2) Open the forward passenger/crew door 831 (841), (Ref. TASK 52-10-00-R 010-001).
R Subtask 53-11-00-020-070
R B. Removal of the Component
R (1) Remove the girt-bar fitting blanking-plates (Ref. TASK 52-11-31-000-R 005).
R Subtask 53-11-00-110-123
R C. Preparation of the Inspection Area
R (Ref. Fig. 659/TASK 53-11-00-991-094)
R WARNING : USE SOLVENTS/CLEANING AGENTS, SEALANTS AND OTHER SPECIAL_______
R MATERIALS ONLY WITH A GOOD SUPPLY OF AIR.
R OBEY THE MANUFACTURERS INSTRUCTIONS.
R PUT ON PROTECTIVE CLOTHING.
R DO NOT GET THEM IN YOUR MOUTH.
R DO NOT SMOKE.
R DO NOT BREATHE THE GAS.
R THESE MATERIALS ARE POISONOUS, FLAMMABLE AND SKIN IRRITANT.
R GET MEDICAL HELP IF YOUR SKIN OR EYES BECOME IRRITATED.
EFF : ALL 53-11-00Page B636 Aug 01/04
CES
R R FWD Door-Cutout Lower-Corners Figure 659/TASK 53-11-00-991-094
EFF : ALL 53-11-00 Page B637 Aug 01/04
CES
R WARNING : OBEY THE MANUFACTURER'S INSTRUCTIONS WHEN YOU USE THIS/THESE_______
R MATERIAL/S.
R USE PROTECTIVE CLOTHING, RUBBER GLOVES, GOGGLES AND A MASK.
R (1) Clean the inspection area with CLEANING AGENTS (Material No. 11-004)
R and a lint-free cotton cloth MISCELLANEOUS (Material No. 19-003), if
R necessary.
R (2) Make sure that the surface of the inspection area is clean and
R smooth.
R (3) Do a visual check of the inspection area for damage or
R discontinuities.
R (4) Make sure that there is no:
R (a) Corrosion damage:
R - If you find corrosion damage, refer to the Structural Repair
R Manual (Ref. SRM 512200,P.Block 001) for types, inspection,
R removal and corrosion protection.
R (b) Other damage (cracks, scratches, stress, marks, dents, bumps...):
R - If you find this type of damage, refer to the Structural Repair
R Manual (Ref. SRM 511100,P.Block 001) for damage classification
R and corrective action.
R 4. Procedure_________
R Subtask 53-11-00-220-091
R A. Inspection
R (Ref. Fig. 659/TASK 53-11-00-991-094)
R (1) Do a detailed inspection of the forward passenger/crew door-cutout
R lower-corners above cabin floor level. This inspection is applicable
R at FR16 and FR20 from STGR22 to STGR23 and around girt bar fittings,
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址：A320飞机维护手册 AMM FUSELAGE 机身1(86)
