76-11-00
ALL ú ú C01 Page 506 ú Jul 15/97
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
////////////////////////A / /
CFM56 ENGINES
737-300/400/500/ /MAINTENANCE MANUAL ////////////////////////
DIMENSION "A"
P DIMENSION "B"
SEE A
SHUTOFF LEVER-CUTOFF POSITION
CHECK CLEARANCE LEVER AND STOP BETWEEN SHUTOFF
COVER SHUTOFF LEVER-IDLE POSITION
CABLE SUPPORT PLATE DIMENSION "A" START CONTROL CABLES WITH ADJUSTABLE LOWER END FITTINGS
MEC FUEL CONTROL BOX R P DIMENSION "B"
SHUTOFF LEVER-CUTOFF POSITION
CHECK CLEARANCE LEVER AND STOP BETWEEN SHUTOFF
COVER SHUTOFF LEVER-IDLE POSITION
START CONTROL CABLES WITH FIXED LOWER END FITTINGS
A NOTE:____ POWER LEVER OMITTED FOR CLARITY.
Start Control System Travel Test Figure 503
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
76-11-00
ALL ú ú C01 Page 507 ú Jul 15/97
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
////////////////////////A / /
CFM56 ENGINES
737-300/400/500/ /MAINTENANCE MANUAL ////////////////////////
(a) START CONTROL CABLES WITH FIXED END FITTINGS; Do these steps to get the correct clearance at the fuel shutoff lever. 1) Make sure there is one or two shims installed between the
cable support plate and the fuel control box. a) If there are no shims installed, install the shims (AMM 76-11-09/401).
NOTE: The shims will increase the adjustment range of
____ the cable approximately 0.25 inch (6.35 mm).
2) Remove the access panel No. 6301 (left wing) or No. 6401 (right wing) from the upper aft surface of the strut (AMM 12-31-71/201).
3) Adjust the upper rodend on the start control cable to get the correct clearance. a) Look through the witness hole to see the depth of the
thread engagement in the rodend. b) Make sure the threads cover not less than 50 percent of the hole.
4) If you cannot adjust the rodend enough to get the correct clearance, do these steps: a) Adjust the jamnuts to change the position of the cable
casing relative to the cable support bracket on the strut drum control box. b) Make sure that not less than two threads on the casing extend beyond the nuts.
(b) START CONTROL CABLES WITH ADJUSTABLE END FITTINGS; Do these steps: 1) Adjust the lower rodend to get the correct clearance.
a) Look through the witness hole to see the depth of the thread engagement in the rodend. b) Make sure the threads cover more than 50 percent of the hole.
2) If you cannot get the correct clearance with the adjustment of the rodend, adjust the jamnuts to change the position of the cable casing relative to the cable support plate. a) Make sure that not less than two threads on the casing
extend beyond the nuts.
(c)
Put lockwire on the checknut and the jamnuts if an adjustment was made.
(d)
If no further adjustments are to be accomplished, do the steps that follow.
S 415-009-C00
(11) Install the aft cover on the fuel control box (View B, Fig. 501).
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
76-11-00
ALL ú ú C01 Page 508 ú Jul 12/99
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
////////////////////////A / /
CFM56 ENGINES
737-300/400/500/ /MAINTENANCE MANUAL ////////////////////////
S 415-010-C00
(12)
Install the access panel on the upper aft surface of the nacelle strut (if removed) (AMM 12-31-71/201).
S 415-011-C00
(13)
Close the left fan cowl (AMM 71-11-02/201).
NOTE: Do not do this and the next step if you want to continue with
____ the adjustment of the thrust control push-pull cable.
S 845-099-C00
(14) Do the procedure: Put the Airplane Back to Its Usual Condition.
G. Adjust the Thrust Control Push-Pull Cable.
S 845-102-C00
(1)
Do the procedure: Prepare for the Adjustment.
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址：737-300 400 500 AMM 飞机维护手册 发动机控制 ENGINE CONTROLS(9)
