S 745-056
(8)
Do the preparation for the DFCS BITE Test in this task:
"Operational Test - Digital Flight Control System"
(Ref 22-11-00/501 or 22-11-01/501).
S 745-016
(9)
Get access to ROLL CWS:
(a)
Push the INIT REF key on the CDU keyboard.
(b)
Push the LSK adjacent to <INDEX.
(c)
Push the LSK adjacent to MAINT>.
(d)
Push the NEXT PAGE key on the CDU keyboard.
(e)
Push the LSK adjacent to <RIGGING.
(f)
Do the preparation steps as shown on the CDU display.
(g)
Push the LSK adjacent to <CONTINUE.
(h)
Push the LSK adjacent to <CWS.
(i)
Push the LSK adjacent to <ROLL CWS.
E. Roll Force Transducer Adjustment
S 035-035
(1) Remove the adjustable end of the transducer:
(a)
Put the shims between the shaft and the drum. The clearance must be 0.020 (+0.003/-0.0).
(b)
Remove the bolt, washer, and nut from the adjustable end of the force transducer.
S 865-036
(2) Find the null voltage:
(a) Do the tests 55.29 and 55.30 of the CWS RIGGING BITE test.
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
22-11-11
ALL ú ú 02 Page 508 ú Mar 12/00
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
737-300/400/500MAINTENANCE MANUAL
(b)
Make sure that the A and B voltage on the CDU display are between +0.80v and -0.80v: 1) Hold the transducer level when you read the voltage for
minimum error.
(c)
Make sure that there are some threads shown on the fine and coarse adjustments.
(d)
Slightly loosen the clamps of the electrical cable to get the voltage down below |80mv, if it is necessary. Tighten the clamps.
(e)
If you measured the voltages of the transducer before the installation, make sure that you get the same voltage.
S 435-037
(3) Install the adjustable rod end of the transducer:
(a)
Remove the lockwire from the locknuts, fine adjustment nut, and the washer tab.
(b)
Loosen the locknuts and adjust the coarse fitting until you can install the bolt, washer and nut.
(c)
Do the fine adjustment until you get the voltage as measured before the installation |10 mv.
NOTE: The fine adjustment is approximately 0.006 inch for
____
each turn.
(d) Adjust the coarse adjustment until the mounting hole is parallel to the mounting hole at the opposite end of the transducer.
NOTE: The coarse adjustment is approximately 0.016 inch for
____
each turn.
(e)
Make sure that the null voltage is still the same |10 mv (minimum).
(f)
Tighten the locknut on the adjustable sleeve (push the washer against the end cap of the transducer).
(g)
Tighten locknut on the rod end.
(h)
Install the lockwire.
(i)
Remove the shims.
S 715-038
(4) Do this check:
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
22-11-11
ALL ú ú 01 Page 509 ú Jul 15/91
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A 737-300/400/500MAINTENANCE MANUAL
WARNING: MAKE SURE THAT PERSONS AND EQUIPMENT ARE CLEAR OF ALL
_______ CONTROL SURFACES BEFORE YOU SUPPLY HYDRAULIC POWER. AILERONS, RUDDER, ELEVATORS, FLAPS, SLATS, SPOILERS, LANDING GEAR, AND THRUST REVERSERS CAN MOVE QUICKLY WHEN YOU SUPPLY HYDRAULIC POWER. THIS CAN CAUSE INJURY TO PERSONS OR DAMAGE TO EQUIPMENT.
(a)
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址：737-300 400 500 AMM 飞机维护手册 自动飞行 AUTOFLIGHT 1(154)
