R Subtask 54-54-00-020-055
R D. Removal of the Fairings
R (1) Remove the aft movable fairing (Ref. TASK 54-55-00-000-001).
R (2) Remove the lower fairing (Ref. TASK 54-56-00-000-001).
R Subtask 54-54-00-020-060
R E. Disconnection of the Drain Lines
R (Ref. Fig. 403/TASK 54-54-00-991-009)
R (1) Disconnect the two drain lines (21) and (22).
R (2) Put blanking plugs on the disconnected line ends.
R Subtask 54-54-00-020-056
R F. Removal of the Plate and the Fitting
R (Ref. Fig. 404/TASK 54-54-00-991-007)
R (1) Remove the bolts (1) and the nuts (2).
R (2) Remove the plate (6).
R (3) Remove the bolts (5) and the nuts (3).
R (4) Remove the fitting (4).
R 4. Procedure_________
R Subtask 54-54-00-020-058
R A. Removal of the Aft Fixed Fairing
R (Ref. Fig. 405/TASK 54-54-00-991-008)
R (1) Remove the screw (17) and the washer (18).
R (2) Disconnect the bonding lead (19).
R (3) Remove the nut (13) and the bolt (11).
R (4) Remove the nut (16), the washer (15), the bolt (14) and the washer
R (12).
R (5) Loosen the nuts (7) and (8).
R R Drain Lines - Aft Fixed Fairing Figure 403/TASK 54-54-00-991-009
1EFF : 1 1 1CES ALL 1 111 54-54-00 Page 410 Aug 01/99
R R Plate and Fitting - Aft Fixed Fairing Figure 404/TASK 54-54-00-991-007
1EFF : 1 1 1CES ALL 1 111 54-54-00 Page 411 Aug 01/99
R R Attach Fittings - Aft Fixed Fairing Figure 405/TASK 54-54-00-991-008
1EFF : 1 1 1CES ALL 1 111 54-54-00 Page 412 Aug 01/99
R (6) Remove the nuts (10) and the bolts (9).
R (7) Remove the aft fixed fairing.
R NOTE : Two persons are necessary to move the aft fixed fairing.
____
TASK 54-54-00-400-001
Installation of the Aft Fixed Fairing
1. Reason for the Job
__________________
There is an alternative method for this procedure. This task gives one of the methods. For the other method, refer to the other task in this page block.
2. Job Set-up Information
______________________
A. Fixtures, Tools, Test and Support Equipment
-------------------------------------------------------------------------------
REFERENCE QTY DESIGNATION
-------------------------------------------------------------------------------
R No specific Torque Wrench : range 0.00 to 1.20 m.daN
R (0.00 to 9.00 lbf.ft) No specific Torque Wrench : range 0.20 to 3.60 m.daN
(2.00 to 26.00 lbf.ft) No specific Torque Wrench : range 1.00 to 10.00 m.daN
(8.00 to 75.00 lbf.ft)
B. Referenced Information
-------------------------------------------------------------------------------
REFERENCE DESIGNATION
-------------------------------------------------------------------------------
20-28-00-912-004 Electrical Bonding of Components With Conductive Bolts and Screws and Bonding Straps in the Fuselage and in the Wings (this does not include the tanks)-
29-00-00-864-001 Put the Related Hydraulic System in the Depressurized
Configuration before Maintenance Action 29-00-00-910-002 Safety Procedures of the Hydraulic System 29-10-00-863-001 Pressurize the Green Hydraulic System 29-10-00-863-002 Pressurize the Yellow Hydraulic System 29-10-00-863-003 Pressurize the Blue Hydraulic System with a Ground
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址:A320飞机维护手册 AMM NACELLES/PYLONS(91)