Maintenance
SRM 511100-P.Block001
SRM 512200-P.Block001
54-51-00-991-013 Fig. 617
3. Job Set-up
__________
Subtask 54-51-00-941-066
A. Safety Precautions
(1)
On the center pedestal, on the ENG panel 115VU:
(a) Put a warning notice to tell persons not to start the engine.
(2)
Make sure that the engine 1(2) shutdown occurred not less than 5 minutes before you do this procedure.
R (3) On the overhead maintenance panel 50VU:
(a) Make sure that the ON legend of the ENG/FADEC GND PWR/1(2) pushbutton switch is off.
(b) Put a warning notice to tell persons not to energize the FADEC. Subtask 54-51-00-010-063
B. Get Access R (1) Put an access platform in position at zones 410 and 420.
(2) Use a FLASHLIGHT for the inspection.
Subtask 54-51-00-040-063
C. Aircraft Maintenance Configuration
(1) Make the thrust reverser unserviceable (Ref. TASK 78-30-00-481-041).
Subtask 54-51-00-110-067
D. Cleaning of the Structure
WARNING : USE SOLVENTS/CLEANING AGENTS, SEALANTS AND OTHER SPECIAL
_______ MATERIALS ONLY WITH A GOOD SUPPLY OF AIR. OBEY THE MANUFACTURERS INSTRUCTIONS. PUT ON PROTECTIVE CLOTHING. DO NOT GET THEM IN YOUR MOUTH. DO NOT SMOKE. DO NOT BREATHE THE GAS. THESE MATERIALS ARE POISONOUS, FLAMMABLE AND SKIN IRRITANT. GET MEDICAL HELP IF YOUR SKIN OR EYES BECOME IRRITATED.
(1) Clean the inspection surface with CLEANING AGENTS (Material No. 11-004) and a lint-free cotton cloth MISCELLANEOUS (Material No. 19-003), if necessary.
4. Procedure
_________
Subtask 54-51-00-220-065
A. Inspection
(Ref. Fig. 617/TASK 54-51-00-991-013)
(1)
Do a detailed inspection of the structure of the fasteners that attach the supports of the access doors between RIB5 and RIB6.
(2)
Make sure that there is no:
(a)
Corrosion damage: If you find corrosion damage, refer to the Structural Repair Manual (Ref. SRM 512200-P.Block001) for types, inspection, removal and corrosion protection.
(b)
Other damage (cracks, scratches, stress, marks dents, bumps,...):
if you find other damage, refer to the Structural Repair Manual R (Ref. SRM 511100-P.Block001) for damage classification and R related corrective action.
5. Close-up
________
Subtask 54-51-00-440-063
A. Aircraft Maintenance Configuration
(1) Make the thrust reverser serviceable (Ref. TASK 78-30-00-081-041).
R R Supports of the Access Doors between RIB5 and RIB6 Figure 617/TASK 54-51-00-991-013
1EFF : 1 1 1CES ALL 1 111 54-51-00 Page 684 Aug 01/03
Subtask 54-51-00-410-066
B. Close Access
(1)
Make sure that the work area is clean and clear of tool(s) and other items.
(2)
Remove the access platform(s).
(3)
Remove the warning notice(s).
1EFF : ALL 1 54-51-00Page 685 1 1 May 01/05R 1 1 1CES 1
R TASK 54-51-00-200-016
R Detailed Inspection of Pylon, Lateral Panels, at the Edge of Access Door
R Cutouts, between RIB 5 and RIB 6, LH/RH
R WARNING : PUT THE SAFETY DEVICES AND THE WARNING NOTICES IN POSITION BEFORE YOU_______
R START A TASK ON OR NEAR:
R - THE FLIGHT CONTROLS
R - THE FLIGHT CONTROL SURFACES
R - THE LANDING GEAR AND THE RELATED DOORS
R - COMPONENTS THAT MOVE.
R 1. Reason for the Job__________________
R Refer to the MPD TASK: 545130-01
R 2. Job Set-up Information______________________
R A. Fixtures, Tools, Test and Support Equipment
R -------------------------------------------------------------------------------
R REFERENCE QTY DESIGNATION
R -------------------------------------------------------------------------------
R No specific warning notice
R No specific 1 ACCESS PLATFORM 3M (10 FT)- ADJUSTABLE
R No specific 1 FLASHLIGHT
R B. Consumable Materials
R -------------------------------------------------------------------------------
R REFERENCE DESIGNATION
R -------------------------------------------------------------------------------
R Material No. 11-004 USA MIL-T-81533
R 1.1.1TRICHLOROETHANE (METHYL CHLOROFORM)
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址：A320飞机维护手册 AMM NACELLES/PYLONS(39)
