(2)
Make sure that there is no:
(a)
Corrosion damage:
-If you find corrosion damage, refer to the Structural Repair Manual (Ref. SRM 512200-P.Block001) for types of corrosion, inspection, removal and corrosion protection.
(b)
Other damage (cracks, scratches, stress, marks dents, bumps,...):
-if you find this type of damage, refer to the Structural Repair Manual (Ref. SRM 511100-P.Block001) for damage classification and corrective action.
5. Close-up
________
Subtask 54-51-00-420-061
A. Installation of the Component
(1) Install the engine (Ref. TASK 71-00-00-400-042).
R 1EFF : ALL 1 54-51-00Page A637 1 1 Feb 01/04 1 1 1CES 1
R Mating Face of the Engine Aft Attachment-Beam Figure 627/TASK 54-51-00-991-040
R 1EFF : 1 1 1CES ALL 1 111 54-51-00 Page A638 Feb 01/04
Subtask 54-51-00-410-076
B. Close Access
(1)
Make sure that the work area is clean and clear of tool(s) and other items.
(2)
Remove the access platform(s).
(3)
Remove the warning notice(s).
R 1EFF : ALL 1 54-51-00Page A639 1 1 Feb 01/04 1 1 1CES 1
R
TASK 54-51-00-220-001
Special Detailed Inspection of Pylon to Wing Aft Attachment Shackles at RIB 10
1. Reason for the Job
__________________
Refer to the MPD TASK: 545123-01
2. Job Set-up Information
______________________
A. Fixtures, Tools, Test and Support Equipment
-------------------------------------------------------------------------------REFERENCE QTY DESIGNATION
-------------------------------------------------------------------------------
No specific warning notice
No specific access platform 2.50 m (8 ft. 2 in.)
B. Consumable Materials
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
Material No. 11-004 USA MIL-T-81533 1.1.1TRICHLOROETHANE (METHYL CHLOROFORM) (Ref. 20-31-00)
Material No. 19-003 USA AMS 3819 LINT-FREE COTTON CLOTH (Ref. 20-31-00)
C. Referenced Information
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
78-30-00-081-041 Make the Thrust Reverser Serviceable after Maintenance 78-30-00-481-041 Make the Thrust Reverser Unserviceable for
Maintenance NTM 545123, P.Block 401 SRM 511100-P.Block 001 SRM 512200-P.Block 001 54-51-00-991-063 Fig. 628
R 1EFF : ALL 1 54-51-00Page A640 1 1 May 01/05 1 1 1CES 1
3. Job Set-up__________
Subtask 54-51-00-941-077
A. Safety Precautions
(1) On the center pedestal, on the ENG panel 115VU:
(a) Put a warning notice to tell persons not to start the engine.
(2) Make sure that the engine 1(2) shutdown occurred not less than 5
minutes before you do this procedure.
R (3) On the overhead maintenance panel 50VU:
(a) Make sure that the ON legend of the ENG/FADEC GND PWR/1(2)
pushbutton switch is off.
(b) Put a warning notice to tell persons not to energize the FADEC.
Subtask 54-51-00-010-076
B. Get Access
R (1) Put an access platform in position:
R (a) At zone 410 for the left pylon.
R (b) At zone 420 for the right pylon.
(2) Remove the access panels:
(a) For the left pylon: 471CL, 472BR, 475AL, 475BL, 476AR, 476BR
(b) For the right pylon: 481BL, 482CR, 485AL, 485BL, 486AR, 486BR
Subtask 54-51-00-040-072
C. Aircraft Maintenance Configuration
(1) Make the thrust reverser unserviceable (Ref. TASK 78-30-00-481-041).
R 1EFF : ALL 1 54-51-00Page A641 1 1 May 01/05 1 1 1CES 1
Subtask 54-51-00-110-078
D. Cleaning of the Structure
WARNING : USE SOLVENTS/CLEANING AGENTS, SEALANTS AND OTHER SPECIAL_______ MATERIALS ONLY WITH A GOOD SUPPLY OF AIR. OBEY THE MANUFACTURERS INSTRUCTIONS. PUT ON PROTECTIVE CLOTHING. DO NOT GET THEM IN YOUR MOUTH. DO NOT SMOKE. DO NOT BREATHE THE GAS. THESE MATERIALS ARE POISONOUS, FLAMMABLE AND SKIN IRRITANT. GET MEDICAL HELP IF YOUR SKIN OR EYES BECOME IRRITATED.
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址：A320飞机维护手册 AMM NACELLES/PYLONS(51)
