(a) Clean the external surfaces of the spigot ball joint, the retaining plate (3) and the bolts (1) with CLEANING AGENTS (Material No. 11-004) and MISCELLANEOUS (Material No. 19-003).
(2)
Do a visual inspection of the spigot ball joint and the spigot.
(3)
Apply BONDING AND ADHESIVE COMPOUNDS (Material No. 08-034) in the housing of the spigot ball joint.
4. Procedure
_________ Subtask 54-51-41-420-050
A. Installation of the Spigot Ball Joint (Ref. Fig. 401/TASK 54-51-41-991-001-A, 405/TASK 54-51-41-991-004-A, 406/TASK 54-51-41-991-005-A)
(1)
Get the R/I TOOL - SPIGOT BALL JOINT (98D54403002102).
(2)
Put the spigot ball joint (32) in its housing.
(3)
Install the threaded rods (43) with the nuts (42) below the upper panel.
1EFF : ALL 1 54-51-41Page 416 1 1 May 01/05R 1 1 1CES 1
R Spigot Ball-Joint Installation Figure 405/TASK 54-51-41-991-004-A
1EFF : 1 1 1CES ALL 1 111 54-51-41 Page 417 May 01/05
Spigot Ball Joint - Protection against Corrosion Figure 406/TASK 54-51-41-991-005-A
1EFF : 1 1R 1CES ALL 1 11 1 54-51-41 Page 418 May 01/05
(4) Install the nuts (41) and tighten them to hold the threaded rods (43) in position.
(5) Install the plate (45) on the threaded rods (43) and the nuts (44).
(6) Tighten the nuts (44) continuously to install the spigot ball joint (32) and to release the half segments (31) and (36).
(7) Remove the nuts (44) and the plate (45).
(8) Remove the nuts (41) and the threaded rods (43).
(9) Apply SEALANTS (Material No. 09-018) on the surface which touches the retaining plate (3) and the inner face of the upper spar.
R R (10) Install the retaining plate (3) on the lower spigot ball-joint fitting.
R R (11) Install the eight bolts (1) with SEALANTS (Material No. 09-025) or SEALANTS (Material No. 09-016) and the nuts (2).
R R NOTE : If you sawed the heads of the two bolts (1) during removal,____ install new bolts (1) with the heads in the down position.
(12) Remove the unwanted sealant with CLEANING AGENTS (Material No. 11-004) and MISCELLANEOUS (Material No. 19-003).
5. Close-up________
Subtask 54-51-41-420-051
A. Installation of Component
(1) Install the fire extinguisher bottles (Ref. TASK 26-21-41-400-004).
Subtask 54-51-41-440-050
B. Close Access
(1) Make the thrust reverser serviceable (Ref. TASK 78-30-00-081-041).
INTENTIONALLY BLANK
R 1 1
54-51-41Page 420
1 1 May 01/05 1 1 1CES 1
Subtask 54-51-41-410-050
C. Installation of Component
(1)
Install the access doors:
(a)
For the right Pylon: 425BL, 425BR.
(b)
For the left Pylon: 415BL, 415BR.
(2)
Install the access panels:
(a) For the right pylon: 481AL, 481BL, 482AR, 482BR.
(b) For the left pylon: 471AL, 471BL, 472AR, 472BR. Subtask 54-51-41-942-050
D. Close Access
(1)
Make sure that the work area is clean and clear of tool(s) and other items.
(2)
Remove the access platform(s).
(3)
Remove the warning notice(s).
(4)
De-energize the ground service network
FORWARD FAIRING - DESCRIPTION AND OPERATION
___________________________________________
1. Description___________ (Ref. Fig. 001) The forward fairing is composed by :
-9 ribs
-2 longitudinal zoning walls (bulkhead)
-A visor supported by spring blades
-1 bottom cap
-Skin
-Fan cowl hinge fittings made of titanium.
All elements except the hinge fittings are made of stainless steel.
-
Compartment B1 includes 2 pressure relief doors calibrated at 200 mbars to prevent any overpressure in case of an air duct failure.
-
Compartment A includes also one pressure relief valve to prevent any
overpressure in case of an air duct failure.
-Monel rivets are used for attachment.
-In some limited areas spot welding is also used.
-All the access panels are bolted.
Forward Fairing
Figure 001
1EFF : ALL 1 54-52-00 Page 2
1 1 Feb 01/98
1 1
1CES 1
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址：A320飞机维护手册 AMM NACELLES/PYLONS(78)
