(a) Put a warning notice to tell persons not to start the engine.
(2)
Make sure that the engine 1(2) shutdown occurred not less than 5 minutes before you do this procedure.
(3)
On the overheat maintenance panel 50VU:
(a) Make sure that the ON legend of the ENG/FADEC GND PWR/1(2) pushbutton switch is off.
(b) Put a warning notice to tell persons not to energize the FADEC. Subtask 54-51-00-010-062
B. Get Access R (1) Put an access platform in position at the zones 415 and 425. R
Subtask 54-51-00-020-055 R C. Removal of the Components
(1) Remove the shackles, the sleeves and the bolts of the aft attach fittings (Ref. TASK 54-51-17-000-002).
Subtask 54-51-00-110-066
D. Cleaning of the Structure
WARNING : USE SOLVENTS/CLEANING AGENTS, SEALANTS AND OTHER SPECIAL_______ MATERIALS ONLY WITH A GOOD SUPPLY OF AIR. OBEY THE MANUFACTURERS INSTRUCTIONS. PUT ON PROTECTIVE CLOTHING. DO NOT GET THEM IN YOUR MOUTH. DO NOT SMOKE. DO NOT BREATHE THE GAS. THESE MATERIALS ARE POISONOUS, FLAMMABLE AND SKIN IRRITANT. GET MEDICAL HELP IF YOUR SKIN OR EYES BECOME IRRITATED.
R R R (1) Clean the inspection surface with CLEANING AGENTS (Material No. 11-004) and a lint-free cotton cloth MISCELLANEOUS (Material No. 19-003), if necessary.
4. Procedure_________
Subtask 54-51-00-220-064
R A. Inspection (Ref. Fig. 616/TASK 54-51-00-991-012)
R R (1) Do a detailed inspection of the structure of the sleeves and the bolts of the pylon-to-wing aft attach-fitting.
(2) Make sure that there is no:
(a) Corrosion damage: If you find corrosion damage, refer to the Structural Repair Manual (Ref. SRM 512200-P.Block001) for types, inspection, removal and corrosion protection.
(b) Other damage (cracks, scratches, stress, marks, dents, bumps,...): If you find other damage, refer to the Structural Repair Manual (Ref. SRM 511100-P.Block001) for damage classification and associated corrective action.
R R Sleeves of the Pylon-to-Wing Aft Attach-Fitting Figure 616/TASK 54-51-00-991-012
1EFF : 1 1 1CES ALL 1 111 54-51-00 Page 679 Aug 01/03
5. Close-up________
Subtask 54-51-00-420-056
R A. Installation of the Components
(1) Install the shackles, the sleeves and the bolts of the aft attach fitting (Ref. TASK 54-51-17-400-002).
Subtask 54-51-00-410-065
R B. Close Access
R (1) Make sure that the work area is clean and clear of tool(s) and other items.
R (2) Remove the access platform(s).
R (3) Remove the warning notice(s).
TASK 54-51-00-200-015
R R Detailed Inspection of Pylon, Lateral Panels, in the Areas of Fasteners Securing the Supports of Access Doors, between RIB 5 and RIB 6, LH/RH
WARNING : PUT THE SAFETY DEVICES AND THE WARNING NOTICES IN POSITION BEFORE YOU_______ START A TASK ON OR NEAR: - THE FLIGHT CONTROLS - THE FLIGHT CONTROL SURFACES - THE LANDING GEAR AND THE RELATED DOORS - COMPONENTS THAT MOVE.
1. Reason for the Job__________________
Refer to the MPD TASK: 545126-01
2. Job Set-up Information______________________
A. Fixtures, Tools, Test and Support Equipment
-------------------------------------------------------------------------------REFERENCE QTY DESIGNATION -------------------------------------------------------------------------------
R R No specific No specific No specific warning notice access platform 3 m (9 ft. 10 in.) 1 FLASHLIGHT
B. Consumable Materials
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
Material No. 11-004 Material No. 19-003 USA MIL-T-81533 1.1.1TRICHLOROETHANE (METHYL CHLOROFORM) (Ref. 20-31-00)USA AMS 3819 LINT-FREE COTTON CLOTH (Ref. 20-31-00)
C. Referenced Information
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
78-30-00-081-041 Make the Thrust Reverser Serviceable after
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址：A320飞机维护手册 AMM NACELLES/PYLONS(38)
