• 热门标签

当前位置: 主页 > 航空资料 > 机务资料 >

时间:2011-03-26 00:07来源:蓝天飞行翻译 作者:admin
曝光台 注意防骗 网曝天猫店富美金盛家居专营店坑蒙拐骗欺诈消费者

 (17)
 Make sure that no liquid goes into the inside of the housing (15).

 (18)
 Dry the surface with a dry lint-free cotton cloth, MISCELLANEOUS (Material No. 19-003).

 (19)
 Apply the high speed tape, BONDING AND ADHESIVE COMPOUNDS (Material No. 08-061) on the top of the housing (15) and the adjacent area of the fuselage (8).


 NOTE : Do not cover the removed flash tube assy (21) with tape.
____
R 1EFF : 001-049, 052-099, 101-149, 151-199, 1 33-48-00Page 406 1201-299, 301-399, 401-499, 1Aug 01/05 1 1 1CES 1


 (20)
 Make sure that the high speed tape is installed correctly. The high speed tape must seal all of the opening for the anti-collision light.

 (21)
 Write in the aircraft technical log that the anti-collision light has a temporary repair.


 (22) Keep the circuit breakers 1LV and 5LV open, safetied and tagged. **ON A/C 051-051,
 Subtask 33-48-00-040-050
 A. Deactivation of the Anti-Collision Lights
 CAUTION : DO NOT TOUCH THE LAMP GLASS WITH YOUR FINGERS.

_______ THE OILS FROM YOUR SKIN WILL QUICKLY CAUSE DETERIORATION OF THE LAMP. IF YOU ACCIDENTALLY TOUCH THE LAMP GLASS, CLEAN IT WITH A LINT-FREE CLOTH.
 (1) Remove the countersunk screws (1) from the lens (23) (Ref. TASK 33-48-11-000-001) or (Ref. TASK 33-48-12-000-001).
 NOTE : Make match marks on the screws (1) and/or their positions to
____ help with the installation procedure (different screw sizes).
 (2)
 Remove and discard the remaining part of the lens (23) and the seal

 (22) or (32).

 (3)
 Remove the countersunk screws (3) from the plate (18).

 (4)
 Lift the light assembly until you can see the electrical connector (9).

 (5)
 Disconnect the electrical connector (9) from the light assembly and support the electrical connector (9).

 (6)
 Remove the screws (2) from the cage (20) and remove the cage (20).

 (7)
 Remove the screws (11) from the housing (12) and remove the housing (12).

 (8)
 Disconnect the electrical connectors (17) from the transformer (13). NOTE : Put identification labels on the electrical leads. This will


____ help you to install the electrical connectors (17) again.
 1EFF : ALL 1 33-48-00Page 407 1 1 Aug 01/05R 1 1 1CES 1


 (9) Carefully remove the reflector (19) from the plate (18).
 NOTE : Remove only the reflector (19) and not the light assembly.

____
 (10)
 Install the transformer (13) in the housing (12) with the screws (11).

 (11)
 Install the plate (18) on the housing (12) with the screws (2).

 (12)
 Make sure that the electrical connectors are clean and in the correct condition.

 (13)
 Connect the electrical connector (9) to the transformer (13).

 (14)
 Install the plate (18) and the seal (14) or (34) on the flange (10) with the countersunk screws (3).

 (15)
 Make and install a cover for the cable hole in the plate (18) from the high speed tape, BONDING AND ADHESIVE COMPOUNDS (Material No. 08-061).

 (16)
 Clean the surface of the fuselage (8) around the anti-collision light with a lint-free cotton cloth, MISCELLANEOUS (Material No. 19-003) made moist with a warm soap solution.

 (17)
 Make sure that no liquid goes into the inside of the plate (18).

 (18)
 Dry the surface with a dry lint-free cotton cloth, MISCELLANEOUS (Material No. 19-003).

 (19)
 Apply the high speed tape, BONDING AND ADHESIVE COMPOUNDS (Material No. 08-061) on the top of the plate (18) and the adjacent area of the fuselage (8).


 NOTE : Do not cover the removed reflector (19) with tape.
____
 (20)
 Make sure that the high speed tape is installed correctly. The high speed tape must seal all of the opening for the anti-collision light.

 (21)
 Write in the aircraft technical log that the anti-collision light has a temporary repair.


 1EFF : 051-051, 1 33-48-00Page 408 1 1 Aug 01/05R 1 1 1CES 1


R (22) Keep the circuit breakers 1LV and 5LV open, safetied and tagged.


R **ON A/C ALL


 TASK 33-48-00-440-001
 Reactivation of the Anti-Collision (Beacon) Lights 6LV and 7LV
 1. Reason for the Job__________________
 Refer to the CDL TASK: 33-4 Upper and lower anti-collision Light lens (cover)
 2. Job Set-up Information______________________
 A. Fixtures, Tools, Test and Support Equipment
 -------------------------------------------------------------------------------REFERENCE QTY DESIGNATION -------------------------------------------------------------------------------
 
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址:A320飞机维护手册 AMM LIGHTS 灯光2(41)