4. Procedure
_________ (Ref. Fig. 201/TASK 33-47-11-991-001) Subtask 33-47-11-420-053
A. Installation of the Logo Light
(1)
Install the bonding lead (12), the washer (13) and the screw (11).
(2)
Connect the electrical connector (10).
(3) apply a layer of SEALANTS (Material No. 09-001) to the spar box skin that will be in contact with the housing logo light (9) and apply a layer of SPECIAL MATERIALS (Material No. 05-013)to the housing logo light surface that will be in contact with the spar box skin.
(4) Put in position the logo light housing (9) and tighten the screws(14).
(5) Apply a layer of SPECIAL MATERIALS (Material No. 05-013) on both sides of the seal (3) and put the seal (3) in position on the logo light housing (9).
(6) Put the frame assy (2) in position on the seal (3) and tighten the screws (1).
(7) Apply a fillet of SEALANTS (Material No. 09-001) between the frame assy contour and the spar box skin surface.
Subtask 33-47-11-370-052
B. Painting
(1) Apply STRUCTURE PAINTS (Material No. 16-016) to the heads of the screws (1).
Subtask 33-47-11-710-051
C. Operational Test
(1) Do an operational test of the logo light (Ref. TASK 33-47-00-710-002).
5. Close-up________
R Subtask 33-47-11-865-057
R R A. Remove the safety clip(s) and the tag(s) and close this(these) circuit breaker(s):
R (1) 2LY, 1LY
Subtask 33-47-11-942-051 R B. Removal of the Equipment
(1)
Remove the ground support and maintenance equipment, the special and standard tools and all other items.
(2)
Remove the access platform(s).
(3)
Remove the warning notice(s).
(4)
Make sure that the work area is clean and clear of tool(s) and other items.
ANTI-COLLISION/STROBE LIGHTING - DESCRIPTION AND OPERATION
__________________________________________________________
1. General
_______
A. The aircraft recognition lighting system is designed as a visual aid to other aircraft, so reducing the possibility of a collosion. The system consists of:
-an anti-collision light providing a high-intensity red flashing light on the top and on the bottom of the aircraft fuselage.
-a strobe light providing a high-intensity white flashing light. One light is installed in each wing tip facing forward and one is installed in the tailcone, below the APU exhaust, facing rearwards.
2. Component Location
__________________
R **ON A/C 001-049, 052-099, 101-149, 151-199, 201-299, 301-399, 401-499,
(Ref. Fig. 001)
**ON A/C 051-051,
(Ref. Fig. 001A)
**ON A/C ALL
-------------------------------------------------------------------------------FIN | FUNCTIONAL DESIGNATION | PANEL|ZONE|ACCESS | ATA | | | | DOOR | REF.
-------------------------------------------------------------------------------3LV PWR SPLY UNIT-UPPER BEACON 244 33-48-36 4LV PWR SPLY UNIT-LOWER BEACON 192 33-48-37 6LV LIGHT-BEACON, LOWER 191 33-48-12 7LV LIGHT-BEACON, UPPER 244 33-48-11
14LV PWR SPLY UNIT-WING TIP STROBE LIGHT 634 634AB 33-48-38 632 15LV PWR SPLY UNIT-L WING TIP STROBE 534 534AB 33-48-38
LIGHT 631 16LV LIGHT-STROBE, R WING TIP 634 33-48-14 17LV LIGHT - STROBE, L WING TIP 534 33-48-14 18LV PWR SPLY UNIT-TAIL CONE STROBE LIGHT 311 33-48-39 19LV LIGHT-STROBE, TAIL CONE 317 33-48-13
R Anti-Collision/Beacon and Strobe Lighting - Component Location Figure 001 (SHEET 1)
R 1EFF : 001-049, 052-099, 101-149, 151-199, 1 33-48-00Page 2 1201-299, 301-399, 401-499, 1Aug 01/05 1 1 1CES 1
R Anti-Collision/Beacon and Strobe Lighting - Component Location Figure 001 (SHEET 2)
R 1EFF : 001-049, 052-099, 101-149, 151-199, 1 33-48-00Page 3 1201-299, 301-399, 401-499, 1Aug 01/05 1 1 1CES 1R Anti-Collision/Beacon and Strobe Lighting - Component Location R Figure 001A (SHEET 1)
R 1EFF : 051-051, 1 33-48-00Page 4 1 1 May 01/05 1 1 1CES 1R Anti-Collision/Beacon and Strobe Lighting - Component Location R Figure 001A (SHEET 2)
R 1EFF : 051-051, 1 33-48-00Page 5 1 1 May 01/05 1 1 1CES 1
3. System Description
__________________
R **ON A/C 001-049, 052-099, 101-149, 151-199, 201-299, 301-399, 401-499,
(Ref. Fig. 002)
**ON A/C 051-051,
(Ref. Fig. 002A)
**ON A/C ALL
(Ref. Fig. 003)
The aircraft recognition lighting system consists of two independent systems
which are designed to operate alternately in synchronization:
-
the anti-collision light system;
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址：A320飞机维护手册 AMM LIGHTS 灯光2(37)
