3. Job Set-up
__________ Subtask 33-46-12-865-064
A. Open, safety and tag this(these) circuit breaker(s):
-------------------------------------------------------------------------------PANEL DESIGNATION IDENT. LOCATION -------------------------------------------------------------------------------
122VU LIGHTING/EXT LT/TAXI AND TAKE OFF/TAXI 1LR W08
Subtask 33-46-12-860-052
B. Aircraft Maintenance Configuration
(1)
Make sure that the aircraft is on a horizontal surface.
(2)
Do a precise leveling (Ref. TASK 08-22-00-200-001).
4. Procedure
_________
(Ref. Fig. 502/TASK 33-46-12-991-006) Subtask 33-46-12-820-052
A. Adjustment of the Taxi Light
(1) Install the screen (2) in front of the aircraft. The distance between the screen and the nose landing gear must be 10 m (32.80 ft.).
NOTE : The screen can be a wooden board with a minimum height of 3 m
____
(9.84 ft.) and a minimum width of 2 m (6.56 ft.).
(2) Angular adjustment of the taxi light
(a) Measure the distance "X" between the aircraft centerline and the ground. To do this, measure the distance between one of the leveling triangles and the ground (Ref. AMM 11-21-08 P.Block 001).
NOTE : To get an accurate distance, the aircraft must be on a
____
horizontal surface.
(b)
Subtract the vertical value 2.48 m (8.13 ft.) from the distance "X". This gives you the value "Y", which is the distance between the ground and the target on the screen. You must adjust the light beam to the center of the target.
(c)
Tighten or loosen the nuts (1) of the lower fork to adjust the light beam on the target.
(d)
Tighten the nuts (1) and make sure that the adjustment is correct.
(e)
Safety the nuts (1) together with MISCELLANEOUS (Material No. 19-010).
5. Close-up
________
Subtask 33-46-12-865-065
A. Remove the safety clip(s) and the tag(s) and close this(these) circuit breaker(s): 1LR
Adjustment of the Taxi Light - Alternative Procedure Figure 502/TASK 33-46-12-991-006- 12 (SHEET 1)
1EFF : 051-051, 1 33-46-12Page 508 1 1 May 01/05 1 1 1CES 1
Adjustment of the Taxi Light - Alternative Procedure Figure 502/TASK 33-46-12-991-006- 22 (SHEET 2)
1EFF : 051-051, 1 33-46-12Page 509 1 1 May 01/05 1 1 1CES 1 LOGO LIGHTS - DESCRIPTION AND OPERATION
_______________________________________
1. General
_______
R The logo lights are installed to give illumination of the airlines emblem
R (logo), which is marked on each side of the vertical fin. They come on in
R conjunction with the navigation lights.
2. Component Location
__________________
(Ref. Fig. 001)
-------------------------------------------------------------------------------FIN | FUNCTIONAL DESIGNATION | PANEL|ZONE|ACCESS | ATA | | | | DOOR | REF.
-------------------------------------------------------------------------------3LY LIGHT-LOGO, L 334 33-47-00 4LY LIGHT-LOGO, R 344 33-47-00
R 3. System Description__________________
R (Ref. Fig. 002)
R The logo lights 4LY and 5LY are installed on the horizontal stabilizer in
R the zones 334 and 344. Each logo light consists of a housing which contains
R the lamp assembly and a step-down transformer. The step-down transformer
R lower the aircraft's 115VAC to 28VAC power supply.
R The toggle switch 'NAV/LOGO' 3LA, installed on the cockpit overhead panel
R 25VU, controls the logo lights together with the navigation lights. The
R toggle switch has these positions:
R - 2,
R - 1,
R - OFF.
R When you set the toggle switch 3LA to the 1 (2) position the logo lights
R come on automatically with the NAV1 (NAV2) lights during the subsequent
R flight phases:
R - taxiing,
R - take off,
R - landing.
4. Power Supply
____________
R (Ref. Fig. 002)
R 115 V AC is supplied to each logo light from the normal busbars 101XP and
R 202XP.This is controlled through the circuit breakers 1LY and 2LY. The
R circuit breakers 1LY and 2LY are installed on the circuit breaker panel
R 122VU.
Logo Lights - Component Location
Figure 001
1EFF : ALL 1 33-47-00 Page 2
1 1 Feb 01/98
1 1
1CES 1
Logo Lights - Schematic 中国航空网 www.aero.cn 航空翻译 www.aviation.cn 本文链接地址：A320飞机维护手册 AMM LIGHTS 灯光2(31)
