Subtask 33-47-00-865-051
B. Make sure that this(these) circuit breaker(s) is(are) closed: -------------------------------------------------------------------------------
PANEL ------ DESIGNATION ------------------------------------------------ IDENT. LOCATION-------------------------
122VU LIGHTING/LOGO/L 2LY V03
122VU LIGHTING/LOGO/R 1LY V02
122VU LIGHTING/EXT LT/TAXI AND TAKE OFF/CTL 2LR W09
4. Procedure_________
Subtask 33-47-00-710-050
A. Do this test.
-------------------------------------------------------------------------------ACTION RESULT -------------------------------------------------------------------------------
1. On the overhead panel 25VU:
R - set the NAV/LOGO control switch 3LA to the '2' position.
2. In the cockpit, on the MCDU:
- push the LGCIU2 line select key.
- push the NEXT PAGE pushbutton
- push the LANDING GEAR SIMULATION line select key.
- push the LH+RH line select key.
R - push the EXTENDED line select key.
R 3. Put the slat/flap control lever to position '2' to extend the flaps (Ref. TASK 27-50-00-866-008)
On the Trimmable Horizontal Stabilizer (THS):
-
the logo lights 3LY and 4LY come on.
On the MCDU:
-
the LGCIU2 MENU page comes on.
-
the LANDING GEAR SIMULATION page comes on.
-
the LANDING GEAR SIMULATION menucomes on.
-
the LH+RH menu page comes on.On the THS:
-
the logo lights 3LY and 4LY go off.On the THS:
-
the logo lights 3LY and 4LY come on.
-------------------------------------------------------------------------------ACTION RESULT -------------------------------------------------------------------------------
4. On the overhead panel 25VU:
R R - set the NAV/LOGO control switch 3LA to the '1' position.
R 5. Put the slat/flap control lever to position '0' to retract the flaps (Ref. TASK 27-50-00-866-009)
R 6. In the cockpit, on the MCDU: - push the RETURN line select key, until the SYSTEM REPORT/TEST menu page comes on.
7. On the overhead panel 25VU:
R - set the NAV/LOGO control switch 3LA to the OFF position.
5. Close-up________
Subtask 33-47-00-860-051
On the THS:
-
the logo lights 3LY and 4LY remain on.
On the THS:
-
the logo lights 3LY and 4LY go off.
On the THS:
-
the logo lights 3LY and 4LY come on.
On the THS:
-
the logo lights 3LY and 4LY go off.
A. Put the aircraft back to its initial configuration.
(1)
On the MCDU, put the BRT switch to OFF.
(2)
Do the procedure of ground configuration after flight configuration (Ref. TASK 32-00-00-860-002).
(3)
De- energize the aircraft electrical circuits (Ref. TASK 24-41-00-862-002).
(4)
Make sure that the work area is clean and clear of tool(s) and other items.
LIGHT - LOGO - MAINTENANCE PRACTICES
____________________________________
TASK 33-47-11-600-001
Servicing of the Logo Light 3LY (4LY)
WARNING : ISOLATE THE ELECTRICAL CIRCUITS FROM THE RELATED EQUIPMENT AND THE
_______
ENVIRONMENT.
WARNING : PUT THE SAFETY DEVICES AND THE WARNING NOTICES IN POSITION BEFORE YOU
_______
START A TASK ON OR NEAR:
-
THE FLIGHT CONTROLS
-
THE FLIGHT CONTROL SURFACES
-
THE LANDING GEAR AND THE RELATED DOORS
-COMPONENTS THAT MOVE. WARNING : MAKE SURE THAT THE TRAVEL RANGES OF THE FLIGHT CONTROLS ARE CLEAR.
_______
MOVEMENT OF FLIGHT CONTROLS CAN CAUSE INJURY TO PERSONS AND/OR
DAMAGE.
NOTE : The procedure is the same for the two logo lights.
____
1.
Reason for the Job
__________________
Self Explanatory
2.
Job Set-up Information
______________________
A. Fixtures, Tools, Test and Support Equipment
-------------------------------------------------------------------------------
REFERENCE QTY DESIGNATION
-------------------------------------------------------------------------------
No specific blanking caps
No specific circuit breaker(s) safety clip(s)
No specific warning notices
No specific access platform 5.0 m (16 ft. 5 in.)
B. Consumable Materials
-------------------------------------------------------------------------------
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址：A320飞机维护手册 AMM LIGHTS 灯光2(34)
