(2)
The temperature signal and difference between Pt and Ps are checked for reasonableness. Test programs are run to validate A/D and D/A conversion, Synchro simulator and atitude rate employ wrap-around (W/A) monitoring to ensure adherence to tolerances. The Arinc 429 transmitter is checked to verify accurate translation of parallel digital inputs to serial format.
(3)
The failure warning contains the circuit necessary to drive the flags on the indicators and to operate monitor circuits in the flight control computers. The computer words containing the results of monitor programs are sent on the output bus, buffered, and captured by the latch. The latch output is amplified by drivers which issue the flag output voltage. Failure of one parameter causes all flag outputs to indicate failure, the master failure relay (K1) to energize, and the TEST VALID WHEN LIT light on the computer front panel to come on.
(4)
The computer power interrupt has the highest priority among the failure warnings and causes a shutdown of the computer. On initial startup or a loss of power for more than three seconds a COLD start signal commands the computer to acquire new data for its memory. The power supply has short circuit and overvoltage protection, which trips the dc power when dc voltage is 120% of normal.
(5)
During normal operations, if the 115 volt ac input drops below a preset level, the power interrupt logic commands the computer to temporarily store critical information. If power loss continues beyond 50 milliseconds a change in reset logic commands a halt to computer operation. If the power level rises above the preset value in 1 to 3 seconds after power interrupt a WARM start commands the computer to continue operating using the data that was temporarily stored in the random access memory (RAM).
J. Self Test Operation
(1) The computer is instructed to perform one of three self test programs which exercise most of the computer operations. Each test is selected by rotating the front panel TEST SELECT switch to the desired test and then pressing the PUSH TO TEST switch to enable the appropriate test program.
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. AIRPLANES WITH EFIS ú
34-12-01
ú ú 13 Page 18 ú Mar 15/95
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A 737-300/400/500MAINTENANCE MANUAL
(2) The FUNCTION test performs computation based on stored (simulated) values of static pressure, pitot pressure and temperature probe inputs. This test sends fixed values on all computer signal output lines. The receiving units may take up to one half minute to stabilize. The SLEW test sets altitude rate to 600 ft/min. The FAIL TEST verifies its integrity of the failure warning circuits and activates all failure warning outputs. When each test is successfully completed the TEST VALID WHEN LIT light comes on within two seconds after test is initiated and all unit readings are stabilized.
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. AIRPLANES WITH EFIS ú
34-12-01
ú ú 11 Page 19 ú Mar 15/95
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A 737-300/400/500MAINTENANCE MANUAL
NOT OK
OK
THERE IS AN ADC PROBLEM - Replace the left (right) ADC (AMM 34-12-11/401). The system is OK.
THERE IS NO AIR DATA SYSTEM PROBLEM - The system is OK.
Air Data System - Troubleshooting
Figure 101
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. AIRPLANES WITH EFIS ú
34-12-01
ú ú 02 Page 101 ú Mar 15/98
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
H26003
A
737-300/400/500MAINTENANCE MANUAL
AIR DATA SYSTEM - ADJUSTMENT/TEST
_________________________________
1. General_______
A. This procedure contains two tasks. The first task is the operational test of the Air Data System (ADS). The second task is the system test of the Air Data System (ADS).
B. This procedure will do a test of the ADC installation, the air data indicators and the pneumatic system.
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址：737-300 400 500 AMM 飞机维护手册 导航 NAVIGATION 1(81)
