-cracks
-damage
-corrosion.
(2)
Examine for the correct condition:
-
the outer parts of the flap drive trunnion
-
the spherical bearing
-
the bonding strap
-
the seal assembly at each end of the inboard flap.
(3)
Examine the inboard flap surface for:
-loose or missing rivets
-skin distortion
-cracks
-corrosion.
NOTE : If necessary, refer to the ASRM (Ref. ASRM 575100) for the
____
correct repair procedure.
R 1EFF : 001-049, 051-061, 101-103, 201-203, 1 57-51-00Page 679 1301-399, 1May 01/05 1 1 1CES 1R **ON A/C 062-099, 104-149, 151-199, 204-299, 401-499,
Subtask 57-51-00-110-082-A
A. Preparation for Inspection
(1) Use a MISCELLANEOUS (Material No. 19-003), made moist with CLEANING AGENTS (Material No. 11-026) to clean:
-
the inboard actuator drive arm
-
the drive strut assembly (track 1)
-
the outer part of the flap drive trunnion and the spherical bearing
-
the seal assembly at each end of the inboard flap assembly
-
the inboard flap upper and lower surfaces.
Subtask 57-51-00-210-054-A
B. Inspection
(1)
Use a flashlight and a mirror to examine the inboard actuator drive arm and the drive strut assembly (track 1) for:
-cracks
-damage
-corrosion.
(2)
Examine for the correct condition:
-
the outer parts of the flap drive trunnion
-
the spherical bearing
-
the seal assembly at each end of the inboard flap.
(3)
Examine the inboard flap surface for:
-loose or missing rivets
-skin distortion
-cracks
-corrosion.
NOTE : If necessary, refer to the ASRM (Ref. ASRM 575100) for the
____
correct repair procedure.
R 1EFF : 062-099, 104-149, 151-199, 204-299, 1 57-51-00Page 680 1401-499, 1Aug 01/05 1 1 1CES 1 **ON A/C ALL
5. Close-up
________ Subtask 57-51-00-410-065
A. Close Access
(1)
Make sure that the work area is clean and clear of tool(s) and other items.
(2)
Remove the GROUND LOCK SLEEVE from the MLG door actuator.
(3) Close the MLG doors (Ref. TASK 32-12-00-410-001). Subtask 57-51-00-865-099
B. Remove the safety clip(s) and the tag(s) and close this(these) circuit breaker(s): 6CV, 8CV.
Subtask 57-51-00-860-057
C. Aircraft Maintenance Configuration
(1) Remove the LOCKING TOOL - FLAP/SLAT CONTROL LEVER from the flap/slat control lever.
(2) Fully retract the flaps (Ref. TASK 27-50-00-866-009). Subtask 57-51-00-942-064
D. Removal of Equipment
(1)
Remove the access platform(s).
(2)
Remove the warning notice(s).
(3)
Remove the safety barriers.
(4)
Remove the ground support and maintenance equipment, the special and standard tools and all other items.
1EFF : ALL 1 57-51-00Page 681 1 1 May 01/04R 1 1 1CES 1
R **ON A/C 001-049, 051-099, 101-105, 151-159, 201-210,
TASK 57-51-00-200-005
R Detailed Inspection of Outer Wing, MLG Support RIB 5, Outboard and Inboard R Faces
WARNING : PUT THE SAFETY DEVICES AND THE WARNING NOTICES IN POSITION BEFORE YOU
_______
START A TASK ON OR NEAR:
-
THE FLIGHT CONTROLS
-
THE FLIGHT CONTROL SURFACES
-
THE LANDING GEAR AND THE RELATED DOORS
-COMPONENTS THAT MOVE.
WARNING : MAKE SURE THAT THE GROUND SAFETY-LOCKS ARE IN POSITION ON THE LANDING
_______
GEAR.
CAUTION : BE CAREFUL WHEN YOU DO MAINTENANCE TASKS ON THE WING TRAILING EDGE:
_______
-
DO NOT CAUSE DAMAGE TO THE ELECTRICAL CABLE RACEWAYS.
-
DO NOT CAUSE DAMAGE TO THE ELECTRICAL CABLE INSTALLATIONS.
-MAKE SURE THAT THE ELECTRICAL CABLES ARE INSTALLED CORRECTLY. INCORRECT INSTALLATION CAN CAUSE DAMAGE.
1. Reason for the Job
__________________
Refer to the MPD TASK: 575150-01
2. Job Set-up Information
______________________
A. Fixtures, Tools, Test and Support Equipment
-------------------------------------------------------------------------------REFERENCE QTY DESIGNATION -------------------------------------------------------------------------------
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址：A320飞机维护手册 AMM WINGS 机翼3(99)
