R **ON A/C 001-049, 051-099, 101-149, 151-199, 201-299, 401-499,
Subtask 57-51-00-010-071
C. Get Access
(1)
Put the access platform below the applicable wing at the forward fittings of the flap track 2, zone 531(631).
(2)
Remove the applicable fairing access panels from the flap track 2 fairing (Ref. TASK 57-55-11-000-001):
-for the left wing, remove 531AB, 531BB
-for the right wing, remove 631AB, 631BB.
**ON A/C 301-399,
Subtask 57-51-00-010-071-A
C. Get Access
(1)
Put the access platform below the applicable wing at the forward fittings of the flap track 2, zone 531(631).
(2)
Remove the applicable fairing access panels from the flap track 2 fairing (Ref. TASK 57-55-11-000-004):
-for the left wing, remove 531CB, 531EB
-for theright wing, remove 631CB, 631EB.
**ON A/C ALL
4. Procedure
_________
(Ref. Fig. 619/TASK 57-51-00-991-020)
Subtask 57-51-00-110-085
A. Preparation for Inspection
(1)
Use a non metallic scraper to remove all sealant from the wing bottom skin, aft of the rear spar, around the flap track 2 forward fitting.
(2)
Use a MISCELLANEOUS (Material No. 19-003), made moist with CLEANING AGENTS (Material No. 11-026) to clean the wing bottom skin, aft of the rear spar, around the flap track 2 forward fittings.
Flap Track 2 - Forward Fittings - Location Figure 619/TASK 57-51-00-991-020
1EFF : 1 1R 1CES ALL 1 11 1 57-51-00 Page A615 May 01/04
Subtask 57-51-00-280-053
B. Inspection
(1) Do a special detailed inspection of the outer wing bottom skin lower surface, aft of the rear spar around the flap track 2 forward fittings (Ref. NTM 57-51-64 PART 6).
NOTE : If necessary, refer to the ASRM (Ref. ASRM 575100) for the
____ correct repair procedure. If the defect is not included in this repair, you must request a procedure from Airbus Industrie.
5. Close-up
________
R **ON A/C 001-049, 051-099, 101-149, 151-199, 201-299, 401-499,
Subtask 57-51-00-410-072
A. Close Access
(1) Install the applicable fairing access panels on the flap track 2 fairing (Ref. TASK 57-55-11-400-001):
-
for the left wing, install 531AB, 531BB
-
for the right wing, install 631AB, 631BB.
**ON A/C 301-399,
Subtask 57-51-00-410-072-A
A. Close Access
(1) Install the applicable fairing access panels on the flap track 2 fairing (Ref. TASK 57-55-11-400-004):
-
for the left wing, install 531CB, 531EB
-
for the right wing, install 631CB, 631EB.
**ON A/C ALL
Subtask 57-51-00-865-086
B. Remove the safety clip(s) and the tag(s) and close this(these) circuit breaker(s): 6CV, 8CV.
Subtask 57-51-00-942-071
C. Removal of Equipment
(1)
Make sure that the work area is clean and clear of tool(s) and other items.
(2)
Remove the TOOL-ZERO LOCKING, FLAP SLAT CTL LEVER from the flap/slat control lever.
(3)
Remove the access platform(s).
(4)
Remove the safety barriers.
(5)
Remove the warning notice(s).
(6)
Remove the ground support and maintenance equipment, the special and standard tools and all other items.
1EFF : ALL 1 57-51-00Page A617 1 1 May 01/04R 1 1 1CES 1
R **ON A/C 001-049, 051-099, 101-149, 151-199, 201-299, 401-499,
TASK 57-51-00-200-009
Detailed Inspection of Outer Wing, Bottom Skin Lower Surface, Aft of Rear Spar, Under Flap Track 2 Fairing
WARNING : MAKE SURE THAT THE GROUND SAFETY-LOCKS ARE IN POSITION ON THE LANDING
_______
GEAR.
WARNING : PUT THE SAFETY DEVICES AND THE WARNING NOTICES IN POSITION BEFORE YOU
_______
START A TASK ON OR NEAR:
-
THE FLIGHT CONTROLS
-
THE FLIGHT CONTROL SURFACES
-
THE LANDING GEAR AND THE RELATED DOORS
-COMPONENTS THAT MOVE.
1. Reason for the Job
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址：A320飞机维护手册 AMM WINGS 机翼3(107)
