(2)
Remove the access platform(s).
(3)
Remove the safety barriers.
(4)
Remove the warning notice(s).
(5)
Remove the ground support and maintenance equipment, the special and standard tools and all other items.
TASK 57-44-00-200-010
R Detailed Inspection of Slat 3, Tracks 7 and 8 Attachments, including Track Rib Lugs, Track Lugs, Bolts, Links and Side Plates, LH/RH
WARNING : MAKE SURE THAT THE GROUND SAFETY-LOCKS ARE IN POSITION ON THE LANDING
_______
GEAR.
WARNING : PUT THE SAFETY DEVICES AND THE WARNING NOTICES IN POSITION BEFORE YOU
_______
START A TASK ON OR NEAR:
-
THE FLIGHT CONTROLS
-
THE FLIGHT CONTROL SURFACES
-
THE LANDING GEAR AND THE RELATED DOORS
-COMPONENTS THAT MOVE.
1. Reason for the Job
__________________
Refer to the MPD TASK: 574402-01
2. Job Set-up Information
______________________
A. Fixtures, Tools, Test and Support Equipment
-------------------------------------------------------------------------------REFERENCE QTY DESIGNATION -------------------------------------------------------------------------------
No specific circuit breaker(s) safety clip(s)
No specific safety barriers
No specific warning notices
No specific adjustable access platform 3.5 m (11 ft. 6 in.)
98D27803000000 1 LOCKING TOOL - FLAP/SLAT CONTROL LEVER
B. Consumable Materials
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
Material No. 11-026 GB DEF-STAN 68-148/1
SOLVENT GENERAL PURPOSE (Ref. 20-31-00)
Material No. 19-003 USA AMS 3819
LINT-FREE COTTON CLOTH (Ref. 20-31-00)
C. Referenced Information
-------------------------------------------------------------------------------
REFERENCE DESIGNATION
-------------------------------------------------------------------------------
27-80-00-866-004 Extending the Slats on the Ground
27-80-00-866-005 Retracting the Slats on the Ground
R 27-84-65-000-001 Removal of the No. 3 Slat
R 27-84-65-400-002 Installation of the No. 3 Slat ASRM 574000 (for corrective action) 57-44-00-991-011 Fig. 605 57-44-00-991-012 Fig. 606 57-44-00-991-004 Fig. 607 57-44-00-991-005 Fig. 608
3. Job Set-up
__________
Subtask 57-44-00-941-057
A. Safety Precautions
(1)
Put warning notices in the cockpit to tell persons not to operate the flaps or slats.
(2)
Put the safety barriers in position.
522(622).
Subtask 57-44-00-860-050
B. Aircraft Maintenance Configuration
(1)
Extend the slats fully (Ref. TASK 27-80-00-866-004).
(2)
Install the LOCKING TOOL - FLAP/SLAT CONTROL LEVER (98D27803000000) on the flap/slat control lever.
Subtask 57-44-00-865-064
C. Open, safety and tag this(these) circuit breaker(s):
-------------------------------------------------------------------------------PANEL DESIGNATION IDENT. LOCATION -------------------------------------------------------------------------------49VU FLIGHT CONTROLS/SLT/CTL AND MONG/SYS1 5CV B06 121VU FLIGHT CONTROLS/SLT/CTL/SYS2 7CV R21
Subtask 57-44-00-010-056
D. Get Access
(1) Put the adjustable access platform in position below the applicable wing leading edge at slat 3, zone 522(622).
4. Procedure
_________ (Ref. Fig. 605/TASK 57-44-00-991-011, 606/TASK 57-44-00-991-012, 607/TASK 57-44-00-991-004, 608/TASK 57-44-00-991-005) Subtask 57-44-00-110-060
A. Preparation for Inspection
(1)
Use a MISCELLANEOUS (Material No. 19-003), made moist with CLEANING AGENTS (Material No. 11-026) to clean the inspection area of slat track 7 shown.
(2)
Use a MISCELLANEOUS (Material No. 19-003), made moist with CLEANING AGENTS (Material No. 11-026) to clean the inspection area of slat track 8 shown.
NOTE : If necessary, refer to the ASRM (Ref. ASRM 574000) for the
____
correct repair procedure.
R **ON A/C 001-049, 051-099, 101-105, 151-199, 201-227,
Subtask 57-44-00-210-055
B. Inspection
(1) Examine the slat 3, tracks 7 and 8 attachment links, side plates, track rib lugs and track lugs. Make sure that:
-there is no corrosion, cracks or damage
-the sealant is in a serviceable condition.
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址：A320飞机维护手册 AMM WINGS 机翼3(50)
