(13)
Safety the nut (3) with the new cotter pin (2).
____
again to align the cotter pin hole.
1EFF : ALL 1 57-51-31Page 412 1 1 May 01/02R 1 1 1CES 1
Subtask 57-51-31-410-050
D. Close Access
(1)
Make sure that the work area is clean and clear of tool(s) and other items.
(2)
Install the applicable aileron (Ref. TASK 27-14-41-400-001).
(3)
Install the applicable access panels:
-
for the left wing, install 575AT, 575MB, 575KB, 575LB, 590AB, 590BB
-
for the right wing, install 675AT, 675MB, 675KB, 675LB, 690AB, 690BB.
Subtask 57-51-31-860-052
E. Pressurize the Hydraulic Systems WARNING : MAKE SURE THAT THE CONTROLS AGREE WITH THE POSITION OF THE
_______ ITEMS THEY OPERATE BEFORE YOU PRESSURIZE A HYDRAULIC SYSTEM.
(1)
Pressurize the Green hydraulic system
(Ref. TASK 29-10-00-863-001).
(2)
Pressurize the Blue hydraulic system
(Ref. TASK 29-10-00-863-003).
Subtask 57-51-31-865-052
F. Remove the safety clip(s) and the tag(s) and close this(these) circuit breaker(s): 15CE1, 15CE2, 16CE1, 16CE2, 5CV, 7CV, 9CV, 11CV.
Subtask 57-51-31-710-050
G. Operational Test WARNING : MAKE SURE THAT THE TRAVEL RANGES OF THE FLIGHT CONTROLS ARE
_______ CLEAR. MOVEMENT OF FLIGHT CONTROLS CAN CAUSE INJURY TO PERSONS AND/OR DAMAGE.
(1)
Do an operational test on the ailerons (Ref. TASK 27-14-00-710-001). During the operational test, make sure that the ailerons move correctly.
(2)
Install the safety collar on the circuit breakers 9CV and 11CV.
5. Close-up
________ Subtask 57-51-31-942-050
A. Removal of Equipment
(1)
Remove the safety barriers.
(2)
Remove the warning notice(s).
(3)
Remove the access platform(s).
(4)
Remove the TOOL-ZERO LOCKING, FLAP SLAT CTL LEVER.
(5)
Remove the ground support and maintenance equipment, the special and standard tools and all other items.
MOUNTING SUPPORTS - REMOVAL/INSTALLATION________________________________________
TASK 57-51-33-000-001
Removal of the No.1 Flap Track Beam
WARNING : PUT THE SAFETY DEVICES AND THE WARNING NOTICES IN POSITION BEFORE YOU_______ START A TASK ON OR NEAR: - THE FLIGHT CONTROLS - THE FLIGHT CONTROL SURFACES - THE LANDING GEAR AND THE RELATED DOORS - COMPONENTS THAT MOVE.
WARNING : MAKE SURE THAT THE GROUND SAFETY-LOCKS ARE IN POSITION ON THE LANDING_______ GEAR.
R R R R R CAUTION : BE CAREFUL WHEN YOU DO MAINTENANCE TASKS ON THE WING TRAILING EDGE:_______ - DO NOT CAUSE DAMAGE TO THE ELECTRICAL CABLE RACEWAYS. - DO NOT CAUSE DAMAGE TO THE ELECTRICAL CABLE INSTALLATIONS. - MAKE SURE THAT THE ELECTRICAL CABLES ARE INSTALLED CORRECTLY. INCORRECT INSTALLATION CAN CAUSE DAMAGE.
1. Reason for the Job__________________
Self Explanatory
2. Job Set-up Information______________________
A. Fixtures, Tools, Test and Support Equipment
-------------------------------------------------------------------------------REFERENCE QTY DESIGNATION -------------------------------------------------------------------------------
No specific No specific No specific safety barrierswarning noticesaccess platform 2.8 m (9 ft. 2 in.)
B. Referenced Information
-------------------------------------------------------------------------------
REFERENCE DESIGNATION
-------------------------------------------------------------------------------
27-54-49-000-001 Removal of the Flap Track 1 Actuator 6205CM(6255CM) 27-54-61-000-001 Removal of the Inboard Flap 27-54-61-000-003 Removal of the Inboard Double-Slotted Flap 57-51-15-000-001 Removal of the Shroud Box 572(672) SRM 514211
**ON A/C 001-049, 051-061, 101-103, 201-203,
57-51-33-991-001 Fig. 401 R **ON A/C 062-099, 104-149, 151-199, 204-299, 401-499,
57-51-33-991-001-A Fig. 401A
**ON A/C 301-399,
57-51-33-991-001-B Fig. 401B
**ON A/C ALL
3. Job Set-up
__________
**ON A/C 001-049, 051-061, 101-103, 201-203,
(Ref. Fig. 401/TASK 57-51-33-991-001) R **ON A/C 062-099, 104-149, 151-199, 204-299, 401-499,
(Ref. Fig. 401A/TASK 57-51-33-991-001-A)
**ON A/C 301-399,
(Ref. Fig. 401B/TASK 57-51-33-991-001-B) 中国航空网 www.aero.cn 航空翻译 www.aviation.cn 本文链接地址：A320飞机维护手册 AMM WINGS 机翼3(135)
